Utax P-4531DN Operation Manual Download | Manualshive

Page: 63 / 352

background image

2-41

Preparation before Use

8

Insert the paper cassette into the slot in the machine. Push it straight
in as far as it will go.

9

Select the media type (plain, recycled, etc.) loaded in the cassette.
(Refer to

Media Type (Setting the cassette paper type) on page 4-33

Load Limit

Clip

IMPORTANT

Load the paper with the print side facing down.

Before loading the paper, be sure that it is not curled or folded.
Paper that is curled or folded may cause paper jams.

Ensure that the loaded paper does not exceed the load limit (see
the illustration on the left).

Set the stack of paper so that it is under the clips (see the
illustration on the left).

The paper length and width guides must be adjusted to the paper
size. Loading the paper without adjusting these guides may
cause skewed feeding and paper jams.

Note

If the machine will not be used for a prolonged period,

protect all paper from humidity by removing it from the
cassettes and sealing it in the paper storage bag.

«
...
61
62
63
64
65
...
»

Summary of Contents for P-4531DN

































































































































































































































































































































































Reviews:

No comments

Related manuals for P-4531DN

Brand: EasyThreed Pages: 4

Brand: EASYPRINT Pages: 37

Brand: Wasp Pages: 2

Brand: Z Corporation Pages: 99

Brand: Xerox Pages: 13

Brand: QuickLabel Systems Pages: 122

Brand: Lexmark Pages: 9

Brand: Olympus Pages: 28

Brand: Tally Pages: 76

Brand: Felix printers Pages: 26

Brand: Ricoh Pages: 236

Brand: oti Pages: 33

RepRap Industrial

Brand: Kuhling&Kuhling Pages: 24

Designer XL PRO

Brand: PICASO 3D Pages: 72

Brand: AccuBANKER Pages: 5

Brand: Epson Pages: 157

Brand: Epson Pages: 97

Brand: Epson Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands