Utax P-4531DN Operation Manual Download

Page: 73 / 352

3-5

Printing

Banner Printing

When a document length from 470.5 mm (18.53") to a maximum of 915mm (36.03") is specified for printing, the print job is
treated as banner printing.

Display the print settings screen.

Click the

Basic

tab.

Click

Page Sizes...

to register the size.

Click

New

Enter the name of the paper.

Enter the length (470.5 mm (18.53") or longer), and width of the
custom paper size being registered.

Click

Save

Click

In the

Print size

menu, Select the page size (name) registered in

steps 4 to 8.

Select

MP Tray

in the

Source

menu.

Select the type of paper in the

Media type

menu.

Click

Max. number of sheets

1 sheet (manual feed)

Paper width

210 mm to 216 mm (8.27" to 8.51")

Paper length

470.5 mm to 915 mm (18.53" to 36.03")

Paper weight

120 to 163 g/m

Media type

Heavy 2

Note

When KPDL is used for "PDL" Settings of the printer

driver, a length setting of 470.5 mm (18.53") or longer is
handled as banner print.

Summary of Contents for P-4531DN

































































































































































































































































































































































Search results

Summary of Contents for P-4531DN

Reviews:

Related manuals for P-4531DN

Brands by name

Popular brands

Utax P-4531DN, Operation Manual

Search results

Summary of Contents for P-4531DN

Reviews:

Related manuals for P-4531DN

Brands by name

Popular brands