Utax P-4531DN Operation Manual Download

Page: 84 / 352

Operation Panel

4-6

Left Select Key / Right Select Key

• These keys only function when the respective key tabs are shown in the message display. Pressing the key executes

the function shown in the message display.

Pressing the key executes the function shown in the message display.

E.g.:

When the menu shown below is displayed, pressing

[Left Select]

(

[Yes]

) prints the file selected. Pressing

[Right Select]

(

[No]

) stops printing and returns to the menu for the previous step.

• These keys only function when the paper jam message has appeared on the message display. A help message will

then appear to facilitate jam clearing in the location.

Print.

Are you sure?

Yes

Menu Map

Summary of Contents for P-4531DN

































































































































































































































































































































































Search results

Summary of Contents for P-4531DN

Reviews:

Related manuals for P-4531DN

Brands by name

Popular brands

Utax P-4531DN, Operation Manual

Search results

Summary of Contents for P-4531DN

Reviews:

Related manuals for P-4531DN

Brands by name

Popular brands