Utax P-4531DN Operation Manual Download

Page: 98 / 352

Operation Panel

4-20

Enter the subject using the numeric keys.

Press

[OK]

. The subject is set and the

Job Log History

reappears.

Personal Info. (Personal information setting)

Select whether to include personal information in the job log.

In the

Job Log History

menu, press





to select

Personal

Info.

Press

[OK]

. The

Personal Info.

screen appears.

Press





to select

Include

Exclude

Press

[OK]

. The setting is stored and the

Job Log History

reappears.

Note

Up to 60 characters can be entered. For details on

entering characters, refer to

Character Entry Method on page

A-2

Personal Info.:

Include

Exclude

Summary of Contents for P-4531DN

































































































































































































































































































































































Search results

Summary of Contents for P-4531DN

Reviews:

Related manuals for P-4531DN

Brands by name

Popular brands

Utax P-4531DN, Operation Manual

Search results

Summary of Contents for P-4531DN

Reviews:

Related manuals for P-4531DN

Brands by name

Popular brands