Utax P-4531DN Operation Manual Download

Page: 199 / 352

4-121

Operation Panel

Security (Security function setting)

The security functions can be set up to protect printer operation and the print data.

The options available in Security are as follows:

• Network Security (Network security setting)...4-122
• I/F Block Set. (External interface block setting)...4-123
• Security Level...4-125
• Data Security (Data Security setting)...4-126

Press

[Menu]

Press





to select

Security

Press

[OK]

. The Login screen appears.

With the

entry field selected, press

[OK]

. The

entry screen is displayed.

Enter the Login User Name using the numeric keys then press

[OK]

The log in screen reappears.

Press





to select the

entry field.

Press

[OK]

. The

entry screen is displayed.

IMPORTANT

To change the Security function settings, the administrator's Login User Name and Login Password

must be entered. For details of the administrator settings, refer to

Administrator on page 4-136

Note

When user login administration is set:

• When logged in as an administrator, the log in screen is

not displayed and the

Security

menu screen is

displayed.

• The setting is not possible when logged in as anyone other

than an administrator. Log in again as an administrator.

Text

ABC

Note

The initial setting for the administrator's Login User

Name is set as shown below.

P-4531DN: 4500

P-5031DN: 5000

P-5531DN: 5500

P-6031DN: 6000

For details on entering characters, refer to

Character Entry

Method on page A-2

6000

Text

ABC

Summary of Contents for P-4531DN

































































































































































































































































































































































Search results

Summary of Contents for P-4531DN

Reviews:

Related manuals for P-4531DN

Brands by name

Popular brands

Utax P-4531DN, Operation Manual

Search results

Summary of Contents for P-4531DN

Reviews:

Related manuals for P-4531DN

Brands by name

Popular brands