Utax P-4531DN Operation Manual Download

Page: 209 / 352

4-131

Operation Panel

User Login

This enables user login administration. This switches the User Login Administration On/Off and sets the authentication
network server.

In the

User Login Set.

menu, press





to select

User

Press

[OK]

. The

User Login

menu screen appears.

Login Type (Enabling of User Login Administration)

Select

Netwk Authentic.

to enable User Login Administration.

In the

User Login

menu, press





to select

Press

[OK]

. The

screen appears.

Press





to select

Netwk Authentic.

Off

Press

[OK]

. The

User Login

menu reappears.

Netwk Auth. Set (Netwk authentication

setting

)

Set the network authentication server.

In the

User Login

menu, press





to select

Netwk Auth.

Set

Press

[OK]

. The

Netwk Auth. Set

menu screen appears.

The options available in Netwk Auth. Set are as follows:

• Server Type (Server type selection)...4-132
• Host Name (Entering of Host Name)...4-132
• Port (Port number setting)...4-132
• Domain Name (Selecting of Domain Name)...4-133

User Login:

Exit

User Login:

Exit

Off

Netwk Authentic.

Note

When

Netwk Authentic.

is selected, set the

network authentication server.

Note

These settings are only displayed when

Netwk Authentic.

has been set as the

Login Type (Enabling of

User Login Administration) on page 4-131

Netwk Auth. Set.:

Port

Exit

Host Name

Server Type

Summary of Contents for P-4531DN

































































































































































































































































































































































Search results

Summary of Contents for P-4531DN

Reviews:

Related manuals for P-4531DN

Brands by name

Popular brands

Utax P-4531DN, Operation Manual

Search results

Summary of Contents for P-4531DN

Reviews:

Related manuals for P-4531DN

Brands by name

Popular brands