Utax P-4531DN Operation Manual Download

Page: 210 / 352

Operation Panel

4-132

Server Type (Server type selection)

Select the type of server for the authentication server.

In the

Netwk Auth. Set

menu, press





to select

Server

Type

Press

[OK]

. The

Server Type

screen appears.

The available server types are as follows:

NTLM
Kerberos
Ext.

Press





to select the desired server type.

Press

[OK]

. The server type is set and the

Netwk Auth. Set

reappears.

Host Name (Entering of Host Name)

Enter the host name for the authentication server.

In the

Netwk Auth. Set

menu, press





to select

Host Name

Press

[OK]

. The

Host Name

screen appears.

Enter the host name using the numeric keys.

Press

[OK]

. The

Domain

screen appears.

Referring to

Domain Name (Selecting of Domain Name) on page 4-

133

, select the domain name for the authentication server.

Press

[OK]

. The host name is registered and the

Netwk Auth. Set

menu reappears.

Port (Port number setting)

Set the Port number for the authentication server.

In the

Netwk Auth. Set

menu, press





to select

Port

Press

[OK]

. The

Port

screen appears.

Server Type:

NTLM

Kerberos

Ext.

Note

Select

Ext.

to perform ID Card Authentication.

Host Name:

Text

ABC

Note

Up to 64 characters can be entered. For details on

entering characters, refer to

Character Entry Method on page

A-2

To enter the IPv6 address, enclose the address in brackets [ ].
(e.g., [3ae3:9a0:cd05:b1d2:28a:1fc0:a1:10ae]:140)

Domain:

----------------

Domain 02

Domain 01

Note

This setting is only displayed when

Ext

. has been set as the

Server Type (Server type selection) on page 4-

132

Port:

9093

Summary of Contents for P-4531DN

































































































































































































































































































































































Search results

Summary of Contents for P-4531DN

Reviews:

Related manuals for P-4531DN

Brands by name

Popular brands

Utax P-4531DN, Operation Manual

Search results

Summary of Contents for P-4531DN

Reviews:

Related manuals for P-4531DN

Brands by name

Popular brands