background image

10

but  leave  an  air  gap  between  piping  and  drain. 

No shutoff of any description shall be placed be-

tween safety relief valve and the boiler, or on the 

discharge pipes between such safety valve and the 

atmosphere.  Installation  of  the  safety  relief  valve 

shall conform to ANSI/ASME Boiler and Pressure 

Vessel Code, Section IV. The manufacturer is not 

responsible for any water damage.

SUPPLY AND RETURN LINES

The packaged boiler unit is set up to receive 1¼” 

NPT supply and return piping from top access. 

NOTE: 

The circulator pump and isolation valves are fur-

nished within a carton inside the boiler cabinet and can be 
installed at the installer preferred location.

CONDENSATE DRAIN REQUIREMENTS

Condensate drain line to be pitched down to floor 

drain at a minimum of ¼” per foot. An external con-

densate pump (not furnished)  may be used if floor 

drain is not available. The condensate pump must 

be designed for flue gas condensate application.

Figure 9b

MULTIZONE BOILER PIPING

WITH ZONE VALVES

NOTE:

 When zoning with circulators, the furnished circulator pump 

should be used as one of the zone pumps. Each stripped end of 

the electrical wires for the circulator pump inside the junction box 

should be taped or wire nutted to prevent short circuits. Unplug the 

circulator pump wiring at the integrated boiler control.

MULTIZONE BOILER PIPING

WITH CIRCULATORS

Figure 9a

SINGLE ZONE BOILER PIPING

Figure 8

CONDENSATE DRAIN PIPING

Figure 10

1/2" UNTHREADED 

PVC PIPING

2" LONG

1/2" UNTHREADED 

PVC ELBOW

1/2" UNTHREADED 

PVC PIPING

3 3/4" LONG

1/2" UNTHREADED 

PVC ELBOW

1/2" UNTHREADED 

PVC PIPING

1 3/8" LONG

1/2" ADAPTER 

MALE NPT x SOCKET WELD 

PVC PIPING

1 3/8" LONG

1/2" UNTREADED

 PVC TEE

1/2" UNTHREADED

PVC PIPING

3 3/4" LONG

TO CONDENSATE DRAIN

(FIELD SUPPLIED)

TO EXHAUST VENT

(2" CPVC)

TO BOILER FLUE OUTLET

(2" CPVC)

2" NPT MALE PVC BUSHING

2" UNTHREADED MALE 

x 2" NPT MALE 

PVC BUSHING

Summary of Contents for UB90 125









































Reviews: