background image

29

DETAILED SEQUENCE OF OPERATION

SAFETY SEQUENCES DURING OPERATION

DRAFT INDUCER TEMPERATURE SAFETY SWITCH

IF DRAFT INDUCER TEMPERATURE REACHES 

TEMPERATURE SAFETY SWITCH SETPOINT, 

SAFETY SWITCH CONTACTS OPEN IMMEDIATELY, 

CLOSING GAS VALVE (LIGHT GOES OUT).

DRAFT INDUCER RUNS THROUGH 30 SECOND 

POST PURGE AND SWITCHES OFF.

CIRCULATOR RUNS WITH THERMOSTAT ON CALL 

FOR HEAT.

WHEN TEMPERATURE SAFETY SWITCH CONTACTS 

REMAKE BEFORE END OF CALL FOR HEAT, CON-

TROL GOES INTO NORMAL LIGHT-OFF SEQUENCE.

LOSS OF COMBUSTION AIRFLOW

IF COMBUSTION AIRFLOW IS LOST WHILE BURNER 

IS FIRING (DIFFERENTIAL AIR PRESSURE SWITCH 

CONTACTS OPEN) GAS VALVE WILL BE DE-ENER-

GIZED.

 VALVE AND FLAME LIGHTS GO OUT.

DRAFT INDUCER RUNS THROUGH 30 SECOND 

POST PURGE.

IF CALL FOR HEAT REMAINS, IBC WAITS 5 MIN-

UTES FOR AIRFLOW TO BE RE-ESTABLISHED.

IF AIRFLOW DOES NOT RE-ESTABLISH CON-

TROL LOCKOUT - PROBLEM WITH COMBUSTION 

AIRFLOW. 

PURGE LIGHT BLINKS. 

CONTROL WILL 

AUTOMATICALLY RESET AFTER 15 MINUTES.

LOSS OF FLAME SIGNAL

IF AN ESTABLISHED FLAME SIGNAL IS LOST WHILE 

CONTROL EXPECTS THAT THE BURNER IS OPERAT-

ING, CONTROL WILL IMMEDIATELY DE-ENERGIZE 

GAS VALVE. 

VALVE AND FLAME LIGHTS GO OUT.

DRAFT INDUCER RUNS THROUGH 30 SECOND 

POST PURGE.

CONTROL WILL ATTEMPT TO RELIGHT BOILER 

3 TIMES. IF FLAME IS NOT PROVEN, CONTROL 

LOCKOUT - PROBLEM ESTABLISHING A FLAME 

SIGNAL. 

VALVE LIGHT IS BLINKING. 

CONTROL 

WILL AUTOMATICALLY RESET AFTER 1 HOUR.

HIGH LIMIT CONTROL

IF BOILER WATER TEMPERATURE REACHES 

HIGH LIMIT (AQUASTAT) SETPOINT, HIGH LIMIT 

N.C. CONTACTS OPEN IMMEDIATELY, CLOSING 

GAS VALVE. 

VALVE AND FLAME LIGHTS GO OUT.

DRAFT INDUCER CONTINUES TO RUN FOR 30 

SECOND POST PURGE AND SWITCH OFF.

CIRCULATOR RUNS AS LONG AS THERMOSTAT 

CALLS FOR HEAT.

WHEN HIGH LIMIT CONTACTS REMAKE BEFORE 

END OF CALL FOR HEAT - CONTROL GOES INTO 

A NORMAL LIGHT-OFF SEQUENCE.

CASTING TEMPERATURE SAFETY SWITCH

IF BURNER OPERATES WHEN BOILER HAS NO WA-

TER, ALUMINUM BOILER SECTIONS HEAT UP RAPIDLY.

CASTING TEMPERATURE SAFETY SWITCH CON-

TACTS WILL OPEN, BREAKING 24 VOLT POWER 

TO IBC. POWER INDICATOR LIGHT GOES OUT. 

REQUIRES MANUAL RESET TO RECLOSE CON-

TACTS. 

POWER LIGHT GOES OUT.

CIRCULATOR PUMP

CIRCULATOR WILL BE ENERGIZED AS LONG AS 

THERMOSTAT CALLS FOR HEAT DURING LOCKOUT.

RECOVERY FROM ANY LOCKOUT REQUIRES 

RESET, WHICH CAN BE ACCOMPLISHED BY:

(A) REMOVING AND REESTABLISHING THE

THERMOSTAT’S CALL FOR HEAT OR TURNING

THE SERVICE SWITCH OFF AND BACK ON;

OR (B) WAITING FOR THE CONTROL TO

AUTOMATICALLY RESET AFTER 15 MINUTES

FOR LOSS OF COMBUSTION AIRFLOW OR

ONE HOUR FOR LOSS OF FLAME.

Summary of Contents for UB90 125









































Reviews: