The Utile Engineering Co. Ltd.
28/07/04
Irthlingborough, Northamptonshire. England
Tel: +44 (0) 1933 650216
Fax: +44 (0) 1933 652738
14
IC101
Reassemble rear end
6.13
Refit sliding blades (7) in their slots after lightly smearing with oil and removing any high spots with fine
emery cloth. Ensure the blades are orientated correctly in their slots.
6.14
Position the bearing seal (14) into position in the coverplate (3) ensuring that the tension spring is facing
the rotor.
6.15
Press the outer race of roller bearing (11) into position in the coverplate (3).
6.16
If coverplate gasket (24) has been replaced, it is essential that they are the same thickness as the
originals, otherwise internal clearances will be affected and could cause serious damage. Lightly smear the
gasket with oil before replacing.
6.17
Place rear coverplate assembly onto cylinder (1) via location dowels (23) and bolt with 4 screws (20) and
with coverplate gaskets (24) in place.
6.18
Ensure bearing assembly is in place on the shaft with the circlip (19).
6.19
Assemble the two seals (30) and felt seal (31) into the rear end cap (5). Both seals (30) are fitted with the
tension spring facing the rotor.
6.20
Fit the thrust washer (15) against the bearing (14) and with the end cap gasket (26) lightly oiled and in
position, carefully slide the end cap assembly onto the coverplate taking care not to damage the seal lips
on the shaft, bolt in place using three screws (22).
6.21
Position coupling (32) in the end of the shaft, ensuring the shaft drive pin (33) fits into the coupling slot.
6.22
Place oil pump gasket (28) in position, ensuring it has been lightly oiled to assist assembly. Bolt oil pump
assembly (27) using screws (29).
Check that the shaft rotates freely by hand before refitting oil pipes. Prime oil pipes before use.
7. Spare
Parts
A stock of the main wearing parts at the installation site is important to the constant availability and smooth running
of the machine. We recommend the following parts and quantities to be kept in stock at the installation site.
Part Number
Description
LGA12
LGA18
LGA26
Quantity
Blade
S 8331/1
S 8331/2
S 8331/3
6
Ball Bearing
H 1062
H 1062
H 1062
1
Roller Bearing – Drive End
H 1061
H 1061
H 1061
1
Roller Bearing – Rear End
H 1020
H 1020
H 1020
1
Mechanical Seal
F 1115
F 1115
F 1115
1
Bearing Seal – Drive End
F 1200
F 1200
F 1200
1
Bearing Seal – Rear End
F 1047/V
F 1047/V
F 1047/V
1
Felt Seal
F 1030
F 1030
F 1030
1
Oil Pump Seal
F 1052/V
F 1052/V
F 1052/V
2
Gasket – Coverplate
K 1062
K 1062
K 1062
2
Gasket – End Cap – Drive End
K 1070
K 1070
K 1070
1
Gasket – End Cap – Drive End
S 8296
S 8296
S 8296
1
Drive Belt / Drive Coupling
1
Always quote the machine serial number when ordering spare parts.
After Sales Service
Contact the address or telephone number shown at the bottom of each page or our local distributor, for any after
sales service, maintenance or service problems.
Contract maintenance, service exchange machines or a site visit by a Utile Engineering Service Engineer can also
be arranged in the same manner.
Utile Engineering can also provide Training Programs for all your requirements, from maintenance repair to
operator and supervisor training. They are structured to give specialist knowledge of our products and procedures
including use of authorised spares. The enacting of the Health and Safety at Work Act focused attention on the
responsibility of all parties, manufacturers, users and repairers on the repair of equipment. We strongly recommend
that repairs should be carried out to the original specification using authorised replacement parts where necessary.
Spare Parts
After Sales Service
