background image

5. INSTRUCTION FOR USE 

 

5.1 Before Weighing 

Make sure that: 

a. The platter is inserted firmly into the 

scale 

b. The scale is placed on a level and strong 

surface. 

c. The scale is turned on. 

d. The 

ZERO INDICATOR

 is on. If not, press 

ZERO/ON

 to set display to zero. 

 

5.2 Weighing 

a. Always place an object onto the platter 

gently. Excessive force applied to platter 

may cause damages to sensor inside scale. 

b. The weight of the object would be displayed 

automatically. 

c. It is a good practice to remove all loads 

from platter after weighing. It would 

prolong the lifetime of scale. 

5.3 Select Weight Unit 

Press 

MODE

 to shift among kg 

à

 decimal 

à

 lb/oz. 

à

 kg weight units. Refer to 

4.2.1

 for internal 

setting procedures. 

 

The weight unit used before power off would 

be employed when the scale is turned on again. 

 

5.4 Turn Backlight (Optional) On/Off 

Press 

MODE

 to shift among various weight units 

with backlight or without backlight. 

 

Even though the backlight function is employed, 

backlight will be automatically turned off when 

a zero weight is detected and remains stable 

for 2 seconds  

 

Backlight will be automatically turned on again 

when a weight is detected. 

 

5.5 Set Displayed Value to Zero when Unloaded 

Pressing the 

ON/ZERO

 can eliminate a positive 

or negative value. After the 

ON/ZERO 

is pressed, 

the 

ZERO INDICATOR

 appears. 

Refer to 

SPECIFICATIONS 

for maximum zero range. 

Summary of Contents for AM-15K










Reviews: