background image

8

Accessories

The following accessories can be purchased from the 

Technical Assistance Service:

--------

The manufacturer accepts no liability if these accessories are 

not used or are used incorrectly.

Operation

There are indications to show which burner each control knob 

operates.

It is essential to ensure that all the burner parts and pan 

supports are correctly installed for the appliance to work 

correctly. Do not swap the burner caps around.

Switching on automatically

If your hob can be switched on automatically (ignition 

sparkers):

1.

Press the chosen burner control knob and turn it 

anticlockwise to the maximum power setting.
While the control knob is still pressed down, sparks are 

produced on all burners. The flame ignites.

2.

Release the control knob.

3.

Turn the control knob to the required setting.

If it does not come on, turn the control knob to the off setting 

and repeat the steps above. This time, press and hold the 

control knob for longer (up to 10 seconds).

Risk of deflagration!

If after 15 seconds the flame does not ignite, switch off the 
burner and open a nearby window or door. Wait at least one 
minute before trying to switch the burner back on.

Safety system

Depending on the model, your hob may have a safety system 

(thermocouple) that prevents the flow of gas if the burners 

accidentally switch off.

To ensure that this device is active:

1.

Switch on the burner as usual.

2.

Without releasing the control knob, press and hold it down 

firmly for 4 seconds after lighting the flame.

Switching off a burner

Turn the corresponding control knob clockwise to the 0 setting.

Power levels

The progressive control knobs can be used to control the 

power needed, from minimum to maximum power.

Additional wok pan support

Only for use on double and 

triple-flame wok burners with 

pans which are more than 

26 cm in diameter, grill pans, 

earthenware casserole 

dishes, large pans with a 

round base, etc.

Additional coffee maker 

support

Only for use on the auxiliary 

burner with pans which are no 

more than 12 cm in diameter.

Setting

Ú

Control knob off

Large flame

Maximum capacity or aperture and elec-

tricity on

Economy flame

š

Minimum capacity or aperture

WKHUPR

FRXSOH

LJQLWLRQ

VSDUNHU

Summary of Contents for GK11TGA













Reviews: