V2 14C003, Manual

ENGLISH

- 5 -

Lumos is an LED flasher unit for indicating the hazards associated 
with the use of automation devoices for gates, garage doors and 
road barriers; any other use is forbidden and inappropriate.

IMPORTANT WARNING

Warning! The installation of the product has to be made by 
qualified personnel, under the laws and rules in force and 
following the instructions of this handbook. 
It is important to respect the following warnings:
•  Check that the voltage of the product is compatible with the 

one on the clamp of the control unit used for the connection 
of the flashing light.

•  Before making the electrical connections, cut electricity off the 

control unit.

REFERENCE OF MARKING SYMBOLS:
The label affixed to the product bears the following symbols that 
have the following meaning:

  continuous current power supply voltage

  protection against electric shock guaranteed by 

  reinforced 

insulation

TECHNICAL FEATURES

Power supply

24 ÷ 300V 
24 ÷ 230V~ 50/60Hz

Consumption

1,15W (230V - 5mA)
1,15W (115V - 10mA)
0,7W (24Vac - 30mA)
0,9W (30Vdc - 30mA)

Intermittence

automatic

Classe di isolamento

II

Protection degree

IP54

Working temperature

-20 ÷ +60 °C

Dimensions

136 x 82 x 35 mm (Fig. 1)
167 x 82 x 60 mm (Fig. 2)

PRELIMINARY CHECK

•  Check the packaging integrity before opening it and, once 
  open, check the product integrity inside it
•  Check that the place chosen for the installation grant the user 
  total visibility of the flashing light from a long distance
•  Check that the surface chosen for the installation is strong 
  and grant a steady fixing 

m

 ATTENZIONE: WARNING: avoid the surfaces where 

seepage in case of rain is possible

INSTALLATION

1. 

To define the points envisaged for installation, bearing in mind 
that it is necessary to fix the flashing unit onto a flat linear 
surface and that the device may only be installed in a vertical 
position (Fig. 1-2)

2.

  Define the groove path for the electric cables 

3.

  Open the case of the flashing light and use the base 

A

 to mark 

the fixing holes if the flashing light has to be installed on an 
horizontal surface (Fig. 1); use the piece 

B

 if the flashing light 

has to be installed on a vertical surface (Fig. 2)

4.

  Fix the base and connect to the terminal board: connect the 

flashing light output of the control unit on the GREEN terminal 
of the flashing light

m

WARNING: use a cable suitable for external use with 

a minimum section of 2x0,5 mm

2

 and a maximum one of 

2x1,5mm

2

5.

  Connect the built-in antenna on the BLUE terminal. 

Respect the silkscreen on the terminal.

m

 WARNING: use a cable RG174

6.

  Seal the holes of the plugs with silicone to avoid seepage of 

water inside the device

7.

  Close the box with the special screws

DISPOSAL

As for the installation, the disposal of the product at the end of its 
effective life must be performed by qualified personnel.
This product is made of various types of material, some of which 
can be recycled while others must be disposed of. 
Enquire about the recycling or disposal systems available for this 
product category in compliance with regulations locally in force.

EU DECLARATION OF CONFORMITY

V2 S.p.A. hereby declare that LUMOS equipment conforms to the 
essential requirements established in directives:

2014/35/UE low voltage directive
2014/30/EU electromagnetic compatibility directive 
RoHS2 2011/65/EC

Racconigi, 01/06/2015
Legal representative, V2 S.p.A.

Antonio Livio Costamagna