ENGLISH
- 42 -
6 - BOOM INSTALLATION
6.1 - SQUARE BOOM
1.
Cut boom
A
to the desired length
NOTE:
if the lights kit is required (code 163615), the modules
have to be installed before mounting the rubber edge
2.
Present the rubber anti-shock profile
B
on the bar before
inserting it and cut it to the desired length
NOTE
: the rubber profile must be 20 cm shorter than the
bar length. If the installation includes the fixed support
(cod.163605), shorten the rubber to prevent it from coming
into contact with the support.
3.
Lubricate the rod and the rubber in the insertion area, then
proceed with the insertion
NOTE
: during insertion the rod experiences tensile stresses
and compressions that might alter its length. DON’T shorten
the rubber and proceed with the next points.
4.
Knead the rubber to take up the extra length caused by
insertion
5.
Fit cap
O
on the side of the rubber close to the barrier cabinet:
a.
pierce the rubber with a 5 mm drill bit at a distance of
15 mm from the end of the rubber
b.
insert sliding insert
N
into the bar guides
c.
Position cap
O
on the rubber, inserting pin
P
into the
hole made on the rubber
d.
Tighten the screw into the seat of insert
N
6.
Fit cap
M
on the other side of the rubber:
a.
Pierce the rubber with a 5 mm drill bit at a distance of
15 mm from the end of the rubber
b.
Position cap
M
on the rubber, inserting pin
P
into the
hole made on the rubber
c.
Pierce the profile with a 2.5 mm drill bit in
correspondence with the screw
d.
Tighten the screw
7.
Insert the cap
D
onto the boom
8.
Mount bracket
E
on plate
F
, and screw in the 4 screws lightly
9.
Insert the boom in bracket
E
until snug and screw in the
4 screws
10.
Insert plastic cover
G
on bracket
E
11.
Apply the reflecting adhesive tape
C
(accessory code 163622)
on the sides of the boom
6.2 - ROUND BOOM
1.
Cut boom
A
to the desired length
2.
Insert stopper
D
on the boom
3.
Mount bracket
E
on plate
F
, and screw in the 4 screws lightly
4.
Insert the boom in bracket
E
until snug and screw in the
4 screws
O
N
P
M
15 mm
Ø 5 mm
15 mm
Ø 5 mm
Summary of Contents for 36A022
