ESP
AÑOL
- 106 -
9 - AUTOAPRENDIZAJE DE LOS TIMPOS DE
TRABAJO
Este menú permite de aprender en modo automático los tiempos
necesarios para abrir y cerrar la puerta.
Durante esta fase el cuadro memoriza tambien la fuerza necesaria
para abrir y cerrar la puerta: estos valores serán utilizados
activando el sensor de obstáculos.
m
ATENCIÓN: para efectuar el procedimiento de
autoprogramación es necesario deshabilitar la interfaz
ADI mediante el menú
i.Adi
. Si hay protecciones que se
controlan mediante el módulo ADI durante la fase de
autoprogramación no estarán activas.
m
ATENCIÓN: Antes de proceder, asegúrese de haber
colocado correctamente los finales de carrera.
1.
Mantenga pulsada la tecla
OK
hasta que en el display se
visualiza
-APP
2.
Suelte la tecla
OK
: en el display se visualiza
ESC
(pulse la tecla
OK
sólo si se desea salir de este menú)
3.
Pulse la tecla
i
: en el display se visualiza
t.LAv
4.
Pulse la tecla
OK
para poner en marcha el ciclo de
autoaprendizaje: en el display se visualiza el panel de control y
se inicia el procedimiento de autoaprendizaje de los tiempos.
4.1
la puerta se activa en cierre hasta el tope o al llegar al
final de carrera de cierre
4.2
la puerta se activa en apertura hasta el tope o al llegar al
final de carrera de apertura.
4.3
la puerta se activa en cierre hasta el tope o al llegar al
final de carrera de cierre
m
ATENCIÓN: durante la fase de programación
automática de los tiempos el motor se mueve a velocidad
reducida.
m
ATENCIÓN: Si se deja que la central salga de la
programación por time out (1 minuto) el sensor de
obstáculo vuelva al valor que estaba programado antes de
efectuar el autoaprendizaje (según los valores por defecto
el sensor es inhabilitado).
Las posiciones de fin del recorrido de apertura / cierre en
cambio siempre son memorizados.
10 - FUNCIONAMIENTO CON HOMBRE
PRESENTE DE EMERGENCIA
Este modo de funcionamiento puede ser usado para mover
la cancela en modo Hombre Presente en casos particulares
como la fase de instalación/mantenimiento o un posible mal
funcionamiento de fotocélulas, costas, finales del carrera o
encoder.
Para activar la función es necesario enviar una orden de START
3 veces (las órdenes deben durar al menos 1 segundo; la pausa
entre los comandos debe durar al menos 1 segundo).
1”
1”
1”
T
>1”
>1”
>1”
La cuarta orden de START activa la cancela en modo HOMBRE
PRESENTE; para mover la cancela hay que mantener activa la
orden START en toda la duración de la maniobra (tiempo T).
La función se desactiva automáticamente tras 10 segundos de
inactividad de la cancela.
NOTA
: si el parámetro
Strt
está programado como
StAn
, el
mando Start (desde bornera o desde el mando a distancia), hace
que se mueva la cancela alternativamente en apertura y en cierre
(diversamente del modo normal a Hombre Presente).
t.LAv
ESC
-APP
Summary of Contents for AYROS
