- 137 -
POR
TUGUÊS
A área 3
representa a programação deste último contador: se
premir uma vez a tecla
h
ou
i
, o valor apresentado no contador
é arredondado aos milhares; se continuar a premir qualquer uma
das teclas, esse mesmo valor aumenta ou diminui 1 000 ou 100
unidades, respectivamente.
A contagem precedentemente exibida é perdida.
11.1 - SINALIZAÇÃO PARA A NECESSIDADE
DE MANUTENÇÃO
Quando o contador dos ciclos que faltam antes da próxima
manutenção chegar a zero, o quadro eléctrico assinala o pedido
de manutenção através de um pré-piscar suplementar de
5 segundos.
A sinalização repete-se no início de cada ciclo de abertura, até o
instalador aceder ao menu de leitura e configuração do contador,
programando eventualmente um número de ciclos após os quais
será novamente pedida a manutenção.
Se não for definido um novo valor (deixando o contador a zero), a
função de sinalização do pedido de manutenção é desactivada e a
sinalização não é repetida.
m
ATENÇÃO: as operações de manutenção devem ser
efectuadas exclusivamente por pessoal qualificado.
11 - LEITURA DO CONTADOR DE CICLOS
O quadro eléctrico KB1 faz a contagem dos ciclos de abertura
do portão completos e, se necessário, assinala a necessidade de
manutenção após um número fixo de manobras.
Estão disponíveis dois contadores:
• Totalizador dos ciclos de abertura completos que não se pode
pôr a zero (opção
tot
do item
Cont
)
• Contador descrescente dos ciclos que faltam antes da próxima
manutenção (opção
SErv
do item
Cont
).
• Contador dos eventos (opção
EvEn
, ver capítulo 12)
Para aceder ao menu, siga as seguintes indicações:
1.
Manter a tecla MENU premida até ser visualizado
-Cnt
no ecrã
2.
Largar a tecla MENU: é visualizado
tot
no ecrã
O esquema mostra como se deve ler o totalizador, o número de
ciclos que faltam antes da próxima manutenção e programar o
número de ciclos que faltam antes da próxima manutenção (no
exemplo: o quadro eléctrico completou 12451 ciclos e faltam
1300 ciclos antes da próxima manutenção).
A área 1
representa a leitura do número total dos ciclos
completos: com as teclas
h
e
i
, é possível alternar a visualização
entre os milhares ou as unidades.
A área 2
representa a leitura do número total dos ciclos que
faltam antes da próxima manutenção: o valor é arredondado para
centenas.
3
2
-Cnt
tot
SEru
EvEn
ESC
-01.3
-02.0
-01.0
-03.0
1
0 12.
.45 1
Summary of Contents for AYROS
