DEUTSCH
- 174 -
PARAMETER
WERT
BESCHREIBUNG
DEFAULT
MEMO
Co.tE
Test der Sicherheitsrippen
Dieses Menü ermöglicht die Einstellung der Methode des Funktionstests der
Sicherheitsrippen
no
no
Test deaktiviert
rESi
Test aktiviert Rippen aus konduktivem Gummi
Foto
Test aktiviert für optische Rippen
S.EnC
Hindernissensor
0
0 - 7
Dieses Menü ermöglicht die Regulierung der Empfindlichkeit des
Geschwindigkeitssensors. Eine Verringerung der Geschwindigkeit unter die
eingestellte Schwelle weist auf das Vorhandensein eines Hindernisses hin.
Wenn
0
eingestellt wird, wird das Hindernis nur erkannt, wenn das Tor
angehalten wird.
Wenn der Sensor anspricht, wird das Tor gestoppt und 3 Sekunden lang in die
entgegengesetzte Richtung gesteuert, um das Hindernis freizugeben.
Bei einem darauf folgenden Start-Befehl wird erneut die vorherige Bewegung
durchgeführt.
i.Adi
Aktivierung der ADI Vorrichtung
Mit diesem Menü kann man die am ADI Verbinder eingesteckte Vorrichtung
aktivieren
BEACHTE
: durch Wahl der Option
Si
und drücken von MENU ruft man das
Konfigurationsmenü der am ADI Verbinder eingesteckten Vorrichtung auf.
Dieses Menü wird von besagter Vorrichtung gesteuert und ist je nach
Vorrichtung verschieden. Siehe Betriebsanleitung der Vorrichtung.
Wenn die Option
Si
gewählt wird, aber keine Vorrichtung eingesteckt ist, zeigt
das Display eine Reihe von Bindestrichen an.
Beim Verlassen des Konfigurationsmenüs der ADI Vorrichtung kehrt man
zur Option
i.Adi
zurück
no
no
Schnittstelle deaktiviert, eventuelle Meldungen werden nicht berücksichtigt
Si
Schnittstelle aktiviert
Ev.di
Ereignis-Anzeige
Wenn diese Funktion aktiviert ist, wird jedes Mal, wenn ein Ereignis die
normale Funktion des Tores (Sicherheitsauslöser, Benutzerbefehl, usw.)
verändert, eine Nachricht auf dem Display angezeigt, die die Ursache angibt.
Si
Si
Si
Funktion aktiviert
no
Funktion deaktiviert
Ev.M
Höhe der Ereignisspeicherung
3
3
0 - 5
Die Ereignisse werden in der Ereignisliste für die Diagnose, je nach dem Wert,
der in diesem Menü konfiguriert wird, gespeichert:
0
Nur Reset- und Programmiervorgänge
1
Unter anderem, die von verschiedenen Tests aufgetretenen Fehler (
Err2
,
Err3
, usw.)
2
Unter anderem, die Ereignisse, die den normalen Betrieb des Tores
(Sicherheitsauslöser, Benutzerbefehl, usw.) ändern.
3
Unter anderem, die Sicherheitsvorrichtungen, die die Aktivierung des
Betriebszyklus verhindert (Stop, usw..)
4
Unter anderem, die Befehle, die ein Betriebszyklus aktiviert haben (Start,
usw..)
5
Unter anderem, die automatische Aktionen der Anlage
(
En.SA
und
t.inA
)
FinE
Ende der Programmierung
Mit diesem Menü kann der Programmiermodus verlassen (voreingestellt oder
benutzerdefiniert), und alle vorgenommenen Änderungen gespeichert werden.
no
no
Weitere Änderungen vornehmen, die Programmierung nicht beenden
Si
Änderungen abgeschlossen: Ende Programmierung
Summary of Contents for AYROS
