- 226 -
POLSKI
9 - SAMOUCZENIE CZASÓW PRACY
To menu pozwala na automatyczną naukę czasów wymaganych
dla otwarcia i zamknięcia bramy.
Podczas tej fazy, centrala sterująca zapamiętuje także siły
potrzebne do otwierania i zamykania bramy: wartości te zostaną
aktywowane przy wykorzystaniu czujnika przeszkód.
m
OSTRZEŻENIE: w celu przeprowadzenia procedury
samouczenia koniecznym jest wyłączenie interfejsu ADI w
menu
i.Adi
.
Jeżeli niektóre zabezpieczenia kontrolowane są
przez moduł ADI, nie będą on aktywne w czasie fazy
samouczenia.
m
OSTRZEŻENIE: UWAGA: przed kontynuowaniem należy
prawidłowo ustawić ograniczniki mechaniczne oraz czujniki
krańcowe.
1.
Nacisnąć i przytrzymać przycisk
OK
do czasu aż na
wyświetlaczu pojawi się
-APP
2.
Zwolnić przycisk
OK
: na wyświetlaczu pojawi się
ESC
(nacisnąć
OK
tylko przy zamiarze opuszczenia tego menu)
3.
Nacisnąć przycisk
i
: na wyświetlaczu pojawi się
t.LAv
4.
Nacisnąć przycisk
OK
w celu aktywowania cyklu samouczenia
czasu pracy: na wyświetlaczu pojawi się panel kontrolny,
rozpocznie się procedura samouczenia czasu.
4.1
Brama zostanie aktywowana w kierunku zamykania do
chwili osiągnięcia położenia krańcowego zatrzymania
albo
zamknięcia.
4.2
Brama zostanie aktywowana w kierunku otwierania do
chwili osiągnięcia położenia krańcowego zatrzymania
albo
otwarcia.
4.3
Brama zostanie aktywowana w kierunku zamykania do
chwili osiągnięcia położenia krańcowego zatrzymania
albo
zamknięcia.
m
OSTROŻNIE: podczas etapu samouczenia czasów, silnik
wykonuje ruch z ograniczoną prędkością.
m
UWAGA: Jeżeli centrala sterująca zostanie
pozostawiona bez wykonywania jakichkolwiek czynności
przez czas wyjścia z trybu programowania (1 minuta),
czujnik przeszkód powróci do wartości, która została
ustawiona przed przeprowadzeniem samouczenia (zgodnie
z domyślnymi wartościami, czujnik jest wyłączony).
Ustawienia położenia wyłącznika krańcowego są natomiast
zawsze zachowywane.
10 - DZIAŁANIE AWARYJNE NA NACISK
CIĄGŁY
Ten sposób działania pozwala na uruchamianie bramy w trybie
„na nacisk ciągły” w szczególnych przypadkach, takich jak faza
montowania / konserwacji lub niewłaściwe działanie fotobarier czy
listew bezpieczeństwa.
Aby uaktywnić funkcję, należy wysłać impuls START 3 razy
(naciskać przycisk przez co najmniej 1 sekundę; przerwa pomiędzy
poleceniami musi trwać co najmniej 1 sekundy).
1”
1”
1”
T
>1”
>1”
>1”
Czwarty impuls START uaktywnia tryb “na nacisk ciągły”; aby
brama otworzyła się, należy trzymać wciśnięty przycisk START
przez cały czas otwierania (czas T).
Tryb ten wyłącza się automatycznie po 10 sekundach
bezczynności bramy.
UWAGA:
Jeśli parametr
Strt
jest ustawiony na
StAn
, impuls
START (podany na zaciski lub z pilota) powoduje ruch bramy
alternatywnie na otwieranie lub na zamykanie (inaczej niż w
normalnym trybie „na nacisk ciągły”).
t.LAv
ESC
-APP
Summary of Contents for AYROS
