VADA FLOW BOSS VFB-DSU Installation Manual Download

Page: 4 / 17

VADA FLOW BOSS

DIGITAL WATER SWITCHING UNIT

VFB-DSU

INSTALLATION MANUAL

INSTALLATION

PREPARING FOR INSTALLATION

For successful installation, ensure you have all pieces required for your product combination.

What we’ve supplied:

What you’ll need to supply:

Vada Flow Boss
Digital Water
Switching Unit

Fittings to suit

Pressure
reduction valve*

Suction pipe
(internal diameter
must be no smaller
than 25mm)

x2 mesh
inline filters

Discharge pipe
(internal diameter
must be no smaller
than 25mm)

16mm hole saw

Thread tape

Access to a 10A
outdoor power point

Inline filter AKA
Y-Strainer

Isolation valve

Swing check valve

Float switch tank

*If the incoming mains pressure to your property is greater than the specified 1000 kPa (10 bar),
you MUST fit a pressure reduction valve of appropriate capacity upstream of the VFB-DSU. The
recommended pressure is 500kPa as per AS/NZS 3500.

Pump cover

Barrel union kit

Summary of Contents for FLOW BOSS VFB-DSU


















Search results

Summary of Contents for FLOW BOSS VFB-DSU

Reviews:

Related manuals for FLOW BOSS VFB-DSU

Brands by name

Popular brands

VADA FLOW BOSS VFB-DSU, Installation Manual

Search results

Summary of Contents for FLOW BOSS VFB-DSU

Reviews:

Related manuals for FLOW BOSS VFB-DSU

Brands by name

Popular brands