ClearVIEW HD-20
SE
QUSB
S
YSTEM
ClearVIEW HD-20
SE
QUSB
S
YSTEM
,
Document Number 342-0936 Rev C
Page 11 of 46
F
IRST
T
IME
S
ET
-
UP WITH THE
C
LEAR
VIEW
HD-20
SE
QUSB
S
YSTEM
The ClearVIEW HD-20
SE
camera in the QUSB Kit was designed to be very easy to use and operate. There is
documentation at the back of this manual for pin-outs of the connectors. Using the HD VIDEO SELECT rotary
switch and CAMERA SETTINGS DIP switches on the back of the camera, set up the camera’s output resolution
and functional preferences. There is a label on the bottom of the camera that identifies the choices.
HUGE USB NOTE:
For best results with USB 2.0 streaming, select video resolution position “0”
(720p/59.94). MJPEG is limited to 720p, so starting higher only adds a layer of scaling. Position “0” also
works well with IP streaming...so please try position “0” first for USB 2.0 UVC Streaming.
Image: ClearVIEW HD-20
SE
Rear Panel Connections
Drawing: Dip Switch and Resolution Label on the Bottom of the HD-20
SE
Setting the Switches:
Set the desired and available HD output resolution for the camera with the Rotary Switch.
Set the IR control frequency of the camera if it is to respond to the IR remote control.
If using the IR forwarding features with a 3
rd
party codec remote, set the IR OUT switch to ON (SW3).
Set the Baud Rate dip switch (SW4) to 9600bps for most applications. Default is 9600 bps for Cat-5/5e/6 systems.
To set the HDMI or DVI color space, use dip switch 7 (SW7).
If inverting the camera, turn the IMAGE FLIP ON (SW8).
All dip switches DOWN with a power cycle loads the default camera settings. Return dips to desired operating position.
DIP Switch Settings Explained:
1. IR 1, 2 and 3 (SW 1 &2):
A single IR remote has the capability of operating up to three different PTZ cameras in a room.
Use these selector dip switches and the selector buttons at the top of the IR remote to select the frequency.
2. IR OUT on/off (SW3):
The IR output is sent out on the RS-232 RJ-45 jack on the back of the camera. Turning on the IR
output will allow IR signals to be transmitted over the Cat-5e cable to the head end from 3
rd
party remotes. When using RS-
232 control or Vaddio CCU controllers (also via RS-232), turn the IR OUT to OFF (up).
3. Baud Rate (SW4):
The options for baud rate are either 9600 or 38,400 bps. The 9600 bps works best with Cat-5e.
4. HDMI Color or sRGB Color space (SW7):
Default is YCbCr. Use sRGB color space with older DVI-D 1.0 equipment or
monitors only. The YCbCr color space is used for HDMI digital video.
5. Image Flip (SW8):
To invert the HD-20, turn the IMAGE FLIP ON (switch down).
6. Dip Switches 5, 6, 9 and 10
: Not used for operation, please leave these dip switches up or in the OFF position.
7. Restore to Factory Defaults
: All DIP switches down and a power cycle will restore the camera to factory defaults.
IR 1
1 & 2 UP
ON
IMAGE
FLIP
OFF
ON
DIP SWITCH SETTINGS
8
1
2
3
4
5
6
7
9
10
HD VIDEO SELECT
720p/59.94
1080i/59.94
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
1080p/59.94
720p/50
1080i/60
1080i/50
2
1
5
4
3
7
6
8
10
9
IR 2
ON
IR 3
ON
IR
OUT
OFF
9600
bps
38400
bps
10
OFF
1080p/50
1080p/25
1080p/30
720p/60
1080p/60
HDMI
COLOR
YCbCr
sRGB
COLOR
9
OFF
6
OFF
5
OFF
HD-20
SE
Rear Panel
HD Video Select Switch
(Set HD resolution)
Camera Settings 10-Pos Dip Switch
(Set functional preferences)
②
①
③
④
⑤
⑥
⑦
All Down
with Power
Cycle for
Defaults
