background image

 

WallVIEW 50i HideAway – Document 341-141 Rev. C 

 

    Page 13 of 14 

 

 

 

 

FCC Part 15/ICES-003 Compliance 

This equipment has been tested and found to comply with the limits for a Class A digital 
device, pursuant to Part 15 of the FCC rules and Industry Canada ICES-003.These limits 
are designed to provide reasonable protection against harmful interference when the 
equipment is operated in a Commercial environment.  This equipment generates, uses, 
and can radiate radio frequency energy and, if not installed and used in accordance with 
the instruction manual, may cause harmful interference to radio communications. 
Operation of this equipment in a residential area is likely to cause harmful interference, in 
which case the user will be required to correct the interference at his/her own expense. 
 
Operation is subject to the following two conditions: (1) This device may not cause 
interference, and (2) This device must accept any interference including interference that 
may cause undesired operation of the device.  Changes or modifications not expressly 
approved by Vaddio could void the user's authority to operate the equipment.

 

European Compliance 

This equipment has been approved in accordance with Council Directive 1999/5/EC 
"Radio Equipment and Telecommunications Equipment". Compliance of the equipment 
with the Directive is attested by the application of the CE mark on the equipment. 

 

EC Declaration of Conformity 

Application of Council Directive(s):  

1999/5/EC Radio equipment and 
Telecommunications Terminal Equipment 
(R&TTE) Directive 
 

Manufacturer's Name:   

 

 

Vaddio, A Division of Photo Control 

Manufacturer's Address: 

4800 Quebec Avenue North. 
Minneapolis, MN 55428 USA 

 
Model: 

    WallVIEW 

50i 

PTZ 

HideAway 

Model 

Number: 

   999-4404-000 

for 

NTSC 

     999-4404-001 

for 

PAL

 

 

Standard(s) to which Conformity is declared:

 

89/336/EEC "Electromagnetic Compatibility (EMC) Directive": 

 

EN 

55022: 

1994 

(Emissions) 

Specification for limits and methods of 
measurement of radio interference characteristics 
of information technology equipment 

EN 61000-3-2:1995/A1/A2:  1998  

Part  3:  Limits - Section 2: Limits for harmonic 
current emissions. 

EN 61000-3-3:1995  

Section 3: Limitation of voltage fluctuations and 
flicker in low voltage supply systems for equipment 
with rated current up to and including 16 A 

EN 55024:  1998 (Immunity) 

Information technology equipment – Immunity 
characteristic 
Limits and methods of measurement 

EN 61000-4-2: 1995/A1:  1998  

 

Electrostatic Discharge 

EN 61000-4-3: 1996/A1:  1998  

 

Radiated RF Immunity 

EN 61000-4-4: 1995  

 

 

Electrical Fast Transients 

EN 61000-4-5: 1995  

 

 

Lighting Surge 

EN 61000-4-6: 1996  

 

 

Conducted RF Immunity 

EN 61000-4-11: 1994  

 

 

Voltage Dips and Voltage Interruptions 

 
 

 

 
 
 
 
 
 
 

COMPLIANCE

 

Summary of Contents for WallVIEW 50i















Reviews: