background image

 

WallVIEW PRO HD1 Installation and User Guide 341-661 Rev. D                                   Page 7 of 14 

Step 9:  For HDX 9000 Series Installs Requiring IR Pass-Thru 

Connect a two-conductor wire to the connectors of both the 
Polycom HDX codec and Quick-Connect Universal PRO rack 
mount box.  Ground from the Universal PRO should be 
terminated to the “-“ port on the HDX 9000 Series codec’s IR input.  
The SIG port on the Universal PRO should be terminated to the 
square wave symbol.  See adjacent drawing for additional detail 

 

Connect the IR output from the Quick-Connect Universal PRO to 
either the IR spring cage IR input on an HDX series codec (where 
available) or a Xantech™ IR probe (compatible models: 282MRP 
or 283M).  The white striped wire on the IR Probe is the Signal 
and the black wire is Ground.   

 
 
 
 
 
 
 
 
 
Step 9:  For HD1 IR Pass-Thru on HDX 7000 and 8000 Series Codecs 

Using the Optional RJ-45 to DB-9 adapter (998-1006-232) with the system, strip and terminate the single wire 
coming out of the back of the adapter, and connect it to the Phoenix-type connector supplied with the Quick-
Connect PRO.  The wire needs to be terminated to the Signal “SIG” pin on the back of the Quick-Connect 
PRO.   

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Step 9:  For TANDBERG Video Switch IR Pass-Thru 

If connecting a Xantech IR Probe to the IR output of the Quick-
Connect Pro, the white striped wire on the probe should be 
connected to the signal “SIG” terminal and the ground, or black 
wire to “GND”. Attach the probe over the IR window of the codec. 
Make sure the dipswitch is in the correct position

 

 
 
 
 
 
 
 

Figure 9:

  Wiring Configuration for 

IR Forwarding feature

 

(optional)

 

Figure 10:

  Required wiring configuration 

for IR Forwarding from the camera IR 
port to codec.  Note:  There is no IR port 
on the front of the HDX 7000 and 8000 
series codecs.  The IR receiver on these 
codecs is imbedded in the camera.  

 

RS-232 Cat. 5 

Single wire from the back of the Optional 
RJ-45 to DB-9 adapter (998-1006-000), 
connected to the IR “SIG” (signal) port via a 
Phoenix-type connector 

Figure 11: 

Terminating Xantech 

Probe cable to 2-position Phoenix 
type connector 

Summary of Contents for WALLVIEW PRO HD1















Reviews: