background image

VAG Operation and Maintenance Instructions • 4

3  Product features

3.1  Features and function description

The VAG DUOJET

®

 Automatic Air Valve is a two-stage single-

chamber air valve for the automatic aeration and venting of pipe-

lines.
The standard version is delivered with (cf. Picture 2):
•  Inner parts made of stainless steel 1.4571 (Except DN 50/PN

16: float made of plastic)

• Screw connection in the outlet (possible to mount to fittings,

elbows, insect protection)

Picture 2: VAG DUOJET

®

 standard version

As an alternative, a version with gate valve (VAG DUOJET

®

 S) as 

well as with an individually calculated orifice plate (VAG DUOJET

® 

Anti-Surge) is available (cf. Picture 3).

Picture 3: VAG DUOJET

®

-S and VAG DUOJET

®

 Anti-Surge Automatic Air Valve

3.2  Applications

The VAG DUOJET

®

 Automatic Air Valve can be used with the fol-

lowing media:
• Water
• Raw and cooling water

The VAG DUOJET

®

 Automatic Air Valve is not suitable 

for seawater, sewage or waste water.

For information about the corresponding temperature 

limits, please refer to the product-related technical documentati-

on (KAT-A 1912). 
In case of alternative  operating conditions and applications, ple-

ase consult the manufacturer.

3.3.3  Venting performance data

The large venting cross-section is for venting large amounts of air 

when starting up the pumping station.

3.3  Performance limits
3.3.1  Minimum pressure

The minimum pressure for sealing the venting cross-sections is 

0.3 bar.

3.3.2  Air inflow performance data

The large aeration cross-section is for aerating with large amounts 

of air when switching off the pumping station.

Picture 4: Air inflow - large cross-section

Picture 5: Air release – large cross-section

Do not remove the protective caps of the connections / flanges 

and the packaging materials until immediately prior to assembly 

into the pipeline.

The valve can be stored in ambient temperatures ranging from 

-20 °C to + 50 °C (protected by adequate covers). If the valve is

stored at temperatures below 0 °C, it should be warmed up to at

least +5° C before installation and before it is put into operation.

Summary of Contents for DUOJET Series












Reviews: