background image

Care and maintenance 7

0020239016_01 ecoTEC plus Operating instructions

13

7 Care and maintenance

7.1 Maintenance

An annual inspection of the product carried
out by a competent person is a prerequis-
ite for ensuring that the product is perman-
ently ready and safe for operation, reliable,
and has a long working life.

7.2 Caring for the product

Caution.
Risk of material damage
caused by unsuitable clean-
ing agents.

Do not use sprays, scouring
agents, detergents, solvents
or cleaning agents that con-
tain chlorine.

Clean the casing with a damp cloth and
a little solvent-free soap.

7.3 Checking the condensate

drain pipework and tundish

The condensate drain pipework and tun-
dish must always be penetrable.

Regularly check the condensate drain
pipework and tundish for faults and,
particularly, for blockages.

You must not be able to see or feel any
obstructions in the condensate drain pipe-
work and tundish.

If you notice a fault, have it rectified by
a competent person.

7.4 Reading maintenance

messages

If the

symbol is shown in the display, the

product requires maintenance work. The
product is not in fault mode but continues
to operate.

Consult a competent person.

8 Decommissioning

8.1 Temporarily decommissioning

the product

Caution.
Risk of material damage due
to frost.

The frost protection and mon-
itoring devices are only active
while the unit is connected to
the power mains and the gas
isolator cock is open.

Temporarily decommission
the product only if no frost is
expected.

Switch off the product via the main
switch installed on-site.

The display goes out.

When decommissioning the product for
an extended period (e.g. holiday), also
close the gas isolator cock.

8.2 Permanently

decommissioning the product

Have a competent person permanently
decommission the product.

9 Recycling and disposal

The competent person who installed
your product is responsible for the dis-
posal of the packaging.

If the product is identified with this

symbol:

In this case, do not dispose of the
product with the household waste.

Instead, hand in the product to a collec-
tion centre for old electrical or electronic
appliances.

Summary of Contents for ecoTEC VU 246/6-5 OVZ





















Reviews: