Vaisala IRIS User Manual Download | Manualshive

Page: 351 / 394

background image

Config/Config ... (serial output port)

This selection determines which serial line output port is used for ribbon displays. Only a
single port is needed since the displays are daisy-chained together. Type the device name in
the form:

/dev/ttyXXX

The

XXX

depends on your system, for example:

• Linux

ttyS0

or

ttyS1

• HP

tty0p0

or

tty0p1

Check with your IRIS System Manager if you are unsure.

Number of Active Sets (1, 2, 3, 4)

This determines how many different active sets you want. In the example, there are two
active sets. You can name active sets by typing in the name that you want and selecting

File

> Save

.

Display Setup Menu

This is turns on the setup menu. The setup menu is used to configure the ribbon display
appearance for each active set.
The display configuration for an active set can be viewed by pushing the button under the
active set name. Note that this does not change the active set on the ribbon displays, that is,
it only effects what is displayed and edited in the setup menu. The button turns yellow to
indicate which set is being viewed/edited. In the example, the setup menu is set to view

RWY

15

(yellow button).

The top of the setup menu shows the display number and is color coded red or green to
indicate whether display status is

OK

or

Dead

. The display numbers correspond to the

"Selector" position (0 to 7) that is configured on each of the ribbon displays. It is
recommended that if, for example, you have 4 displays, that the selector switches on the
displays be set to 0, 1, 2, and 3.
There is also a button next to the Display Number to select whether a display is enabled or
not. If a display is installed, the button should be clicked-in. In the example, the first four
displays (0 to 3) are enabled, but displays 1, 2 and 3 are dead (read color) indicating that
they are either turned-off or there is a communication problem.
Belowh each display number is a display name (for example,

Tower1

). Set these to indicate

the location or function of the particular ribbon display. It is recommended that you use the
text

None

or

Unused

to indicate the case when a display is not installed. To change the

name, type the text.

Appendix D – IRIS TDWR Features

RESTRICTED

349

«
...
349
350
351
352
353
...
»

Summary of Contents for IRIS











































































































































































































































































































































































































Reviews:

No comments

Related manuals for IRIS

Brand: TechniSat Pages: 19

Brand: HanRongDa Pages: 16

Fulbourn II FUL-DAB-BLK-2

Brand: MAJORITY Pages: 27

Brand: OK. Pages: 73

StreamCaster 4000 Series

Brand: Silvus Pages: 155

Cobra CB 29 LX LE

Brand: Giant Pages: 6

Brand: Motorola Pages: 87

Brand: Motorola Pages: 60

Brand: AvaLAN Pages: 9

RF-DAB-BEDSIDE1

Brand: Renkforce Pages: 76

Brand: Goodmans Pages: 2

Brand: M/A-Com Pages: 46

Brand: Icom Pages: 2

Brand: Clint Pages: 30

JL JL-334 JL-334

Brand: jWIN Pages: 12

Brand: Aluratek Pages: 48

Brand: Clinton Electronics Pages: 60

Brand: Roadstar Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands