background image

All rights reserved. Any logos and/or product names are trademarks 

of Vaisala or its individual partners. Any reproduction, transfer, 

distribution or storage of information contained in this document is 

strictly prohibited. All specifications — technical included — are 

subject to change without notice.

PUBLISHED BY

Vaisala Oyj

Vanha Nurmijärventie 21

FI-01670 Vantaa, Finland

© Vaisala 2022

Safety

Regulatory information: 

https://docs.vaisala.com/access/sources/dita/map?aton_code=M212845EN

When working with equipment in extremely cold temperatures, use appropriate 

personal protective equipment such as thermally insulated gloves and clothing.

Wear personal protective equipment (PPE).

WARNING! 

Failure to comply with these precautions or with specific warnings elsewhere 

in these instructions violates safety standards of design, manufacture, and intended use 

of the product. Vaisala assumes no liability for the customer’s failure to comply with these 

requirements.

WARNING! 

Assess the risks from the installation work. Take into account also the effects 

of local weather conditions.

WARNING! 

When performing installation and maintenance procedures at the roadside, 

follow local and state legislation and regulations on road safety

WARNING! 

Follow local and state legislation and regulations on occupational safety.

WARNING! 

The sensor contains batteries, which poses a fire, explosion, and severe burn 

hazard. Do not crush, disassemble, heat above 100 °C (212 °F), or incinerate.

WARNING! 

The batteries must be removed from the sensor during the recycling. The 

recycling of batteries must only be conducted by fully trained personnel of licensed 

recyclers. 

WARNING! 

Do not leave the battery in an environment surrounded by extremely high 

temperatures. Extremely high temperature can result in an explosion or the leakage of 

flammable liquid or gas.

WARNING! 

Make sure that the battery is not subjected to an extremely low air pressure. 

Extremely low air pressure can result in an explosion or the leakage of flammable liquid or 

gas.

WARNING! 

Only use batteries delivered with the sensor by Vaisala.

CAUTION! 

Changes or modifications to this equipment not expressly approved by the 

party responsible for compliance could void the user's authority to operate the 

equipment.

CAUTION! 

The sensor requires a separation distance of at least 20 cm (7.87 in). This 

distance must be maintained between the user and the device when the device is 

operating.

WARNING!

 alerts you to a serious 

hazard. If you do not read and follow 

instructions carefully at this point, 

there is a risk of injury or even death.

CAUTION! 

warns you of a potential hazard. 

If you do not read and follow instructions 

carefully at this point, the product could 

be damaged or important data could be 

lost.

M212844EN

Summary of Contents for TempCast FMP102













Reviews: