background image

Important Safety Instructions

,

H

!

!

3

Valcom, Inc.
5614 Hollins Road
Roanoke, VA  24019
USA

P. 540-563-2000
F. 540-362-9800
www.valcom.com

Valcom, Inc.
5614 Hollins Road
Roanoke, VA  24019
USA

P. 540-563-2000
F. 540-362-9800
www.valcom.com

|

NOTICE

•  Do not install the clock outdoors. 

Damage to the clock if placed outdoors 
voids the warranty.

•  Do not hang objects from the clock or clock 

mounting parts. The clocks are not designed 
to support the weight of other objects.

•  The clock face and housing may be cleaned 

with a damp cloth or disinfectant. Test 
other cleaning products on a small part of 
the clock housing before attempting to use 
on the rest of the clock. Avoid bleach and 
chemicals known to dissolve plastics.

VERY IMPORTANT:

KNOW YOUR COMMUNICATION PROTOCOL

The Valcom V-D110XXB Digital clocks are designed to support various 3-wire (sync-wire) communication 
protocols. To run each protocol properly, the clock requires the correct wiring format. It is very important 
that you only follow the wiring instructions appropriate to your clock’s communication protocol. Using the 
wrong wiring format may damage the clock.

WARNING

FIRE HAZARD

•  Always follow your national and regional 

electrical codes or ordinances. 

•  The AC power circuit for the clock must 

be attached to a circuit breaker that can 
be reset by the user.

PHYSICAL INJURY HAZARD

•  If you are standing on an object while 

installing your clock, make sure that the 
object can support your weight, and will not 
sway or move as you stand on it. 

•  Take precautions to avoid injury by potential 

safety hazards near the point of installation 
including (but not limited to) heavy 
machinery, sharp objects, hot surfaces, or 
exposed cables carrying an electric current. 

•  Follow all mounting instructions exactly as 

stated in this manual. Failure to do so may 
result in the device falling off the point of 
installation.

•  Packaging materials and mounting items 

include plastic bags and small pieces, which 
pose a suffocation hazard to young children.

DANGER

SHOCK HAZARD

•  Keep the electricity to this device turned 

OFF until the clock installation  
is complete. 

•  Do not expose the clock movement to 

water, or install the clock in a location 
where it may be exposed to water.

Summary of Contents for V-2425B-6
















































Reviews: