5
15
1
30
16
V-9937
TONE
LEVEL
CONTROL
INPUT 3
INPUT 3
LEVEL
ADJUST
POWER
REVERSAL
LED
OUTPUT 2
OUTPUT 1
VOLUME:
OUTPUT 2
OUTPUT 1
TONE SELECT:
V-9942
(Optional)
V-9942
Connector
ON OFF ON OFF
SW2
SW1
Speaker Connections:
Speakers receiving background music:
___ a. Connect pin 7 of V-9937 to Tip of the
amplified speaker assembly.
___ b. Connect pin 22 to Ring of the Speaker.
___ c. Connect pin 6 to -24VDC terminal of
speaker (white lead if using horns).
___ d. Connect pin 21 to GND terminal of
speaker (black lead of horns).
Speakers not receiving background music:
___ a. Connect pin 9 of the V-9937 to Tip of the
amplified speaker assembly.
___ b. Connect pin 24 to Ring of the speaker.
___ c. Connect pin 8 to -24VDC terminal of
speaker (white lead if using horns).
___ d. Connect pin 23 to GND terminal of
speaker (black lead of horns).
Go to the Volume Adjustment section.
Wiring Arrangement 2
Page Access:
___ a. Connect V-9937 pin 4 to page port Tip.
___ b. Connect pin 19 to page port Ring.
Override Access:
___ a. Connect V-9937 pin 1 to override trunk (or
override line key) Tip.
___ b. Connect pin 16 to override Ring.
Music Input:
NOTE: Background music may only be
connected if the telephone system provides
the appropriate inputs.
___ a. Connect music source to telephone
system following phone system installation
instructions.
Speaker Connections:
___ a. Connect pin 7 of V-9937 to Tip of the
amplified speaker assembly.
___ b. Connect pin 22 to Ring of the speaker.
___ c. Connect pin 6 to -24VDC terminal of
speaker (white lead if using horns).
___ d. Connect pin 21 to GND terminal of
speaker (black lead of horns).
NOTE: Set speaker volume controls at
approximately 1/2 volume during installation.
Volume Adjustment and Test
Refer to Figure 4 for location of volume controls.
Test the system and adjust the controls as follows:
NOTE: For proper operation, the controls
must be adjusted in the order specified.
___ 1.
Set the "Output 1" and the "Output 2"
controls to approximately 1/2 volume. Set
the "Input 3" control fully
counterclockwise.
___ 2. Connect a lineman's test set to the V-9937
pins 1 and 16.
___ a. Go "off hook" and speak. Paging should
be heard through the speakers.
___ b. If paging is not heard, recheck
connection. Refer to the Troubleshooting
Chart.
___ c. While speaking, adjust the individual
speaker volume controls to the desired
level.
___ 3. If using wiring Arrangement 1 with
background music, the "Input 3" control
may be adjusted to set the desired level of
background music.
___ 4. If using wiring Arrangement 2, access the
page port through the Telephone System
and use the "Input 3" control to set the
proper system page level.
NOTE: The "Output 1" and the "Output 2"
controls may be used as master controls to
change the system volume.
Tone Module Option
The V-9942, Tone Module Card, may be added to
provide two types of electronic tone signaling over
the paging. An installation may use one or both
types of signaling. Check the type of signaling
being used:
___ 1. Interrupted warble tone (one second tone
every four seconds).
___ 2. A single frequency non-interrupted tone.
The tones are activated by connecting the
appropriate pins together (typically through a dry
contact closure).
The single tone will override the warble tone if
both are accessed at the same time. If a page is
in progress, the tone will be mixed with the page.
FIGURE 5
LOCATIONS OF SWITCHES AND CONTROLS
