background image

 

 

Issue 7 

 

 

1

 947740 

 

 
 

 

V-9940 

EXPANDABLE STATION LEVEL PAGE ADAPTER 

 

INTRODUCTION 

The V-9940 is an Expandable Station Level 
Page Adapter designed to provide ring trip and 
page access circuitry for use on standard device 
telephone lines.  These instructions contain the 
specifications and information necessary to 
install, operate and maintain the V-9940 
Expandable Station Level Page Adapter. 

 

I

MPORTANT

:

   

Please review dip switch 

settings (page 3) for equipment suitability. 

 

FCC Information 

When installing the V-9940, contact the local 
Telephone Company and give them the 
following information: 

  The telephone number of the line to which 

the V-9940 will connect; 

  The FCC Registration #:  BAF9I7-13957-

OT-N; 

  The ringer equivalence number:  1.1A 

 
If the V-9940 is disconnected from its present 
line, contact the local Telephone Company to 
make them aware of the change. 
 
Telephone Company Procedures: the goal of 
the telephone company is to provide the best 
service possible.  In order to do this, it may 
occasionally be necessary for them to make 
changes in their equipment, operations or 
procedures.  If these changes potentially affect 
the service or the operation of customer 
equipment, the Telephone Company will give 
written notice to allow any changes necessary to 
maintain uninterrupted service. 

 

SPECIFICATIONS 

Access Methods 

 Centrex 

numbers 

  Loop start and ground start central office 

lines 

  PABX station numbers 

 
Figure 1 depicts a block diagram of a typical 
PABX installation. 
 

 

 
 
 
 
 
 
 
 
 
 
 
 

Features 

  Ring trip on first ring 

  600 Ohms output; 8 Ohms output with AGC 

  Multiple units may be used for multi-zone 

paging with all call behind a PABX 

  Use with Valcom multi-zone page control 

unit for multi-zone paging Centrex or C. O. 
lines (DTMF signaling only) 

  Use with Valcom handsfree page units for 

talkback paging 

  Background music input 

  Open loop detect reset 

  Audio sensing circuit for reset 

  Time out reset 

 Manual 

reset 

  Answer verification tone 

  All call override tone 

  Battery reversal indicator 

  Auxiliary Make/Break contact 

  Built in 66 type connection block 

  Complies with UL 145 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for V-9940













Reviews: