background image

Venting Installation

IMPORTANT: This appliance’s venting system is room sealed and 
therefore, does not require room air to be used in the combustion process.
1.  Rough-in two 3” diameter vent liners into the existing chimney 

system from the roof. Be careful not to tear or damage the liners in 
the process. It may be easier to install both liners at the same time 
rather than one at a time. Leave plenty of liners at the bottom to 
facilitate the connection of the liners to the vent slider. 

It is best to 

leave the top termination until later.
Designate and mark the top and bottom of one liner as 
“EXHAUST” to avoid confusion later.

2.  a) Large cavity opening

Slide the appliance into the cavity.

b) Smaller cavity opening

Release the two screws retaining the vent slider to the 
front of the 

fi

 rebox.

Remove the slider from the 

fi

 rebox by sliding it towards 

the back of the 

fi

 rebox.

3.  Apply RTV sealant to the collars on the vent slider and 

fi

 t the 

two liners 

ensuring that the exhaust liner is connected to 

the identifi ed “EXHAUST” vent collar

. Secure with 4 tapping 

screws per liner.
If the vent slider was removed from the 

fi

 rebox, slide the 

fi

 rebox 

onto the vent slider in the cavity taking care not to damage the 
liners. 

Make sure that the rear edge of the slider is hooked over 

the cleat on the fi rebox. 

Secure the vent slider to the front of the 

fi

 rebox with two screws removed earlier.

4.  From the roof, pull 

the liners and 

fi

 t the 

fl

 ashing.

5.  Fit the terminal 

cap 

ensuring that 

the exhaust liner 
is connected to 
the exhaust vent 
collar

. Secure with 

8 screws provided.

6.  Seal the terminal 

and 

fl

 ashing from 

water penetration 
as required.

1

3

4

5

Appliance Preparation

option 2b

option 2a

6

Vent slider 
cleat

WARNING

Failure to position the parts in 

Failure to position the parts in 
accordance with these diagrams or 

accordance with these diagrams or 
failure to use only parts speci

fi

 cally 

failure to use only parts speci

fi

 cally 

approved with this appliance 

approved with this appliance 
may result in property damage or 

may result in property damage or 
personal injury.

personal injury.

WARNING

!

23

QUALIFIED 
INSTALLER

Summary of Contents for Legend 739ILN







































Reviews: