background image

27

Owner’s Information

Read the Safety 
Information on 
pages 3 and 5 of 
this manual.

Operating Your 
Stove

For your safety, this appliance is 

fi

 tted with a 

fl

 ame 

supervision device which will shut-off the gas supply 
if, for any reason, the pilot 

fl

 ame goes out. This device 

incorporates a 

fi

 xed probe, which senses the heat 

from the pilot 

fl

 ame. If the probe is cool, the device will 

prevent any gas 

fl

 ow unless manually lighting the pilot. 

See full lighting instructions on page 35 of this manual.

Cleaning

Important - Glass cleaning - Mineral deposits

One of the by-products of the combustion process in 
a gas appliance is a mineral which can show up as a 
white 

fi

 lm on the ceramic glass of the viewing door.

The composition of the deposit varies widely with 
location and time. It is believed to be associated with 
the varying sulfur content of the gas. You may have the 
problem intermittently.

Performance of LPG appliances may be affected by 
the quality of commercial gas supplied in your area.

We have consulted with ceramic glass manufacturers 
and they cannot offer a de

fi

 nitive solution to this 

problem. Dealers have tried various cleaning products 
with varying results. The following are recommendations 
only and are not meant to guarantee results.

NOTE: This is a problem beyond Miles Industries’ 
control and is not covered under warranty.

•  Clean the glass regularly as soon as you notice 

the buildup (white 

fi

 lm). If the 

fi

 lm is left for a longer 

period of time, it will bake on. It is then much harder, 
if not impossible, to remove.

•  NEVER use an abrasive cleaner on the ceramic 

glass. Any abrasion of the surface has the 
immediate effect of compromising the strength of the 
glass. An emulsion type cleaner is recommended.

•  Use a soft damp cloth to apply the cleaner. Dry the 

glass with a soft, dry, preferably cotton cloth. Most 
paper towels and synthetic materials are abrasive to 
ceramic glass and should be avoided.

•  Our dealers have had good results from the 

products listed below. We cannot, however, 
guarantee the results of these products.

 

»

B

RASSO

, P

OLISH

 P

LUS

 by K

ELKEM

, C

OOK

 T

OP

 C

LEAN

 

C

REME

 by E

LCO

, W

HITE

 O

FF

 by R

UTLAND

, T

URTLE

 W

AX

DO NOT CLEAN THE GLASS WHILE IT IS HOT

Always securely replace the window before lighting. 

If broken, the glass pane may only be replaced 
as a complete window unit as supplied by the 
manufacturer.

To remove the window for cleaning:
Rotate its four fastening studs 90 degrees to release 
and gently pull the window unit outwards. Set aside in 
a safe place to avoid damage.

To re

fi

 t the window, place it on its frame and hold it in 

place while pushing and turning its fastening studs 90 
degrees. Then, apply light hand pressure against the 
window frame sides to bed-in the window seal.

Warranty 
Card at the 
back of this 
manual.

WARNING

DO NOT TOUCH THE GLASS WHILE IT IS HOT! 

DO NOT TOUCH THE GLASS WHILE IT IS HOT! 

Let the 

fi

 replace cool 

fi

 rst before cleaning it.

Let the 

fi

 replace cool 

fi

 rst before cleaning it.

WARNING

EXTREMELY HOT!!!

Some parts of your 

fi

 replace are 

EXTREMELY 

HOT

, particularly the window.

DO NOT LET CHILDREN

 touch the glass or any 

parts of your 

fi

 replace even after it is turned off as 

it is still hot.

USE A SAFETY SCREEN or a GATE

 to reduce 

the risk of burns.

Keep the remote control handset 

OUT OF REACH

 

of children.

Avoid placing decorating objects sensitive to heat 
within 36 inches (0.9 m) around the 

fi

 replace.

Do not put

 

furniture or other objects 

in this space in front of 

the fireplace:

36” (0.9 m)

Fireplace

Hearth

x 4

OWNER’S INFO

Summary of Contents for Madrona MF28ILN













































Reviews: