background image

1

©2020, Miles Industries Ltd.

4001168-10

Note: This kit must be installed or serviced by a qualified 

installer, service agency or gas supplier. These instructions 

are to be used in conjunction with the main installation 

instructions for the above listed heater model.

President ZC Cast Front 536CXB

Approved for use with 

Valor heater model 530 only

HOT GLASS

 WILL 

CAUSE BURNS.

DO NOT TOUCH 

GLASS 

UNTIL COOLED.

NEVER 

ALLOW CHILDREN 

TO TOUCH GLASS.

DANGER

!

A barrier designed to reduce the risk of burns from the hot 
viewing glass is provided with this appliance and must be 
installed for the protection of children and other at-risk 
individuals.

INSTALLER: Leave this 

manual with the appliance.
CONSUMER: Retain this 

manual for future reference.

INSTALLATION MANUAL

Portrait

Not compatible with 530INI/IPI insert engines

WARNING

If the information in these 

instructions is not followed 

exactly, a fire or explosion 

may result causing property 

damage, personal injury or 

loss of life.

Applications

The President ZC Cast Front 536CXB is intended to 

install on the Valor Portrait 530 heater when installed as 

a zero clearance fireplace. 
The President ZC Cast Front 536CXB is NOT compatible 

with the 530INI/IPI insert engine. If installing the 530 

insert, use the President ZC Cast Front 536CXBI.

Summary of Contents for President ZC Cast Front 536CXB



















Reviews: