background image

MAINTENANCE

Regular maintenance

In order to achieve and maintain high levels of personal safety and performance
efficiency, it is essential that the opening at the back of the fire and the flue are kept
clear of any form of obstruction. It is possible that deposits of mortar or soot could fall
and accumulate causing the flue to be blocked or restricted and so preventing proper
clearance of dangerous exhaust fumes.
In the United Kingdom it is the law that a landlord must have any gas appliance, flue
and pipework which is situated in a tenant’s premises checked for safety at least every
twelve months by a competent person (In the U.K, a CORGI registered installer).
We recommend that all gas appliances and their flues, wherever situated, are checked
annually.

Servicing

In the United Kingdom servicing can be carried out either by a Valor service 
engineer or a CORGI registered installer.

If you require your fire to be serviced, please contact 

Valor Service

on 

08706 090 

081

and quote the following details;

Model name and number.
Appliance serial no. (To be found on the plate close to the control knob.) 

If you wish to replace any of the owner replaceable parts listed below, spare parts 
are available nationwide via the ‘

interpart stockist network

’. For your local 

stockist consult Yellow pages under Central Heating.
When ordering please quote the part number shown below.

Owner Replaceable Parts

Description

Part No

Ceramic rear wall 

0579399

Coal model

Front coal 

5108541

Rear base coal

5108542

Pack of loose coals

0582839

Pebble model

Front pebble

5108543

Rear base Pebble

5108544

Pack of loose Pebbles

3002773

Page 16

OWNER GUIDE

Summary of Contents for quantum 746


















Reviews: