Service and Installation Manual
For warranty service, call 1-888-VALPRO8 / 1-813-502-030
4
•
Use two or more people to move and install ice maker. Failure to do so can
result in back or other injury.
•
To ensure proper ventilation for your ice maker, the front of the unit must be
completely unobstructed. Choose a well-ventilated area with temperatures
above 50ºF (10ºC) and below 100ºF (38ºC). This unit MUST be installed in
an area protected from the elements, such as wind, rain, water spray or drips.
•
The ice maker should not be located next to ovens, grills or other sources of
high heat.
•
The ice maker must be installed with all electrical and water connections in
accordance with state and local codes. A standard electrical supply, properly
grounded in accordance with the National Electrical Code and local codes
and ordinances, is required.
•
Do not kink or pinch power supply cord or drain lines between ice maker
and cabinet.
•
The fuse (or circuit breaker) size should be 20 amperes.
•
It is important for the ice maker to be leveled in order to work properly. You
may need to make several adjustments to level it.
•
All installations must be in accordance with local plumbing code
requirements.
•
Make certain that the hoses are not pinched or kinked or damaged during
installation.
•
Check for leaks after connection.
•
Remove the packing materials and clean the ice maker before using.
•
Turn on the water supply tap before switching on the ice maker. Never turn
the water supply tap off when the ice maker is working.
•
Except to take ice from the unit, keep the door closed in order to reduce ice
melting and to promote proper ice formation.
•
Although the unit has been tested at the factory, due to long-term transit and
storage, the first batch of cubes must be discarded.
•
Press the STANDBY button to switch off the unit. DO NOT unplug it when
the unit is on.
•
If the ice maker will not be used for a long time, before the next use it must
be thoroughly cleaned. Follow carefully any instructions provided for
cleaning or use of sanitizing solution. Do not leave any solution inside the
ice maker after cleaning.
•
DO NOT touch the condenser fins. The condenser fins are sharp and can be
easily damaged.
•
DO NOT use solvent-based cleaning agents or abrasives on the interior.
Service and Installation Manual
25
For warranty service, call 1-888-VALPRO8 / 1-813-502-030
When this LED is on, the unit is working in the cleaning mode.
6.
Cleaning Recommended (White) LED:
Cleaning Recommended
indicator light
When this LED is on green shows the water filter work well. When this
LED is on yellow shows the water filter work well but approaching
working bad. When this LED is on red shows the water filter should be
replaced by a new one.
7.
ICE button
While the unit is in Stand-by mode (all LEDs is on), you can press ICE
button to start the Automatic Ice Making procedure. The green ice making
indicator light will be on.
8.
CLEAN button
While the unit is in Stand-by mode (all LEDs is on), you can press CLEAN
button to start the Automatic Clean procedure. The green Clean Cycle
indicator light will be on.
9.
STANDBY button
While the unit is in ice-making or cleaning mode, you can press
STANDBY button to enter the Stand-by mode
：
A-
When the unit is in ice-making stage, and you press the STANDBY
button, ice machine will enter the ice harvest mode directly (ice
harvest indicator light will be on). After ice harvest is over, the
unit will drain out the water in the water tank (standby indicator
light will flash). Then the unit will be in the Stand-by mode, and
the standby indicator light will be on.
B-
When the unit is in ice harvest stage, and you press the STANDBY
button, after ice harvest is over, the unit will drain out the water in
the water tank (standby indicator light will flash). Then the unit
will be in the Stand-by mode, and the standby indicator light will
be on.
C-
When the unit is in bin full, water enter water tank or cleaning stage,
and you press the STANDBY button, ice machine will drain out
the water in the water tank directly (standby indicator light will
flash). Then the unit will be in the Stand-by mode, and the standby
indicator light will be on.
IMPORTANT:
•
The ice cube size is set well before the ice machine packaging in the factory,
if it is not necessary, we do not recommend adjust the ice cube size often.
Summary of Contents for VPIM-420
Page 2: ......
