background image

     

Service and Installation Manual

 

9                                   

For  warranty  service,  call  1-888-VALPRO8  /  1-813-502-030                 

                       

 

 

Installation clearance 

                       
 

  Top view                                    Side view 

5"

5"

5"

5"

 

 

 

To ensure proper ventilation for your ice maker, the front of the unit must be 
completely unobstructed. 

 

When installing the ice maker under a counter, follow the recommended 
spacing dimensions shown. Allow at least 5

(127mm) clearance at rear, 

sides and top for proper air circulation. The installation should allow the ice 
maker to be pulled forward for servicing if necessary. 

 

If you choose a built in installation, there is no minimum clearance 
requirement for top and sides. 

 

Choose a well-ventilated area with temperatures above 50ºF (10ºC) and 
below 100ºF (38ºC). This unit MUST be installed in an area protected from 
the elements, such as wind, rain, water spray or drips. 

 

The unit should not be located next to ovens, grills or other sources of high 
heat. 

 

Installation of the ice maker requires a cold water supply inlet of 1/4

(6.35 

mm) soft copper tubing with a shut-off valve. 

 

The ice maker requires a continuous water supply with a minimum pressure 
of 20 psig and a static pressure not to exceed 80 psig. The temperature of the 
water feeding into the ice maker should be between 41ºF (5ºC) and 90ºF 
(32ºC) for proper operation. 

                                                                                     

 

Rear 
 
 
 
 
 
 
 
Front   

   

Service and Installation Manual   

 

 

 

             

For warranty service, call 1-888-VALPRO8 / 1-813-502-030                         

         

18

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 

Normal Sounds 

Your new ice cube machine may make sounds that are unfamiliar to you. Most 
of the new sounds are normal. Hard surfaces like the floor and walls can 
amplify the sounds. The following describes the kinds of sounds that might be 
new to you and what may be causing them. 

 

Rattling noises may come from the flow of the refrigerant or the water 
line. Items stored on top of the ice cube machine can also make noises. 

 

The high-efficiency compressor may make a pulsating or high-pitched 
sound. 

 

Running water may make a splashing sound. 

 

You may hear air being forced over the condenser by the condenser fan. 

 

During the Harvest cycle, you may hear the sound of ice cubes falling 
into the ice storage bin. 

 
 
 
 
 

 

 

Evaporator 

Water 
tank (trough) 

Water 
pump 

Fan 
motor 

Condenser 

Compressor 

Hot gas valve 

Summary of Contents for VPIM55

















Reviews: