Valtra VALMET 6000 Workshop Manual Download

Page: 514 / 1361

135

Model

Code

Page

37. Autocontrol 5 / 5.2

1. 8. 2000

370

6250--8950

1. 9. 2002

B. Gas pedal calibration in AC 5 and 5.2

Gas pedal is calibrated, if:

--- DPS has malfunctions

--- Test mode indicated (table

on page

370/10

), that the

gas pedal function is not within the given limits

--- Fault code

A313

appeared in the display.

--- Fuel injection pump position sensor has been changed

--- According to the maintenance program (also check that

change in links between pump and sensor does not affect

the function of the system).

--- fuel injection pump has been changed or adjusted

Important!

Before calibration, check the pedal sensor volt-

ages in AC 5, see page

370/24

. Before activating the gas

pedal calibration, the engine revs must be at the low idling

speed and in the normal operating temperature (over +30

C). Also the transmission must be in the normal operating

temperature.

1. Activate the setting mode according to instr. A on page

370/14.

2. Select in the setting mode menu number 1 with the DPS

push buttons (in the speed gear lever knob) and confirm it

with the DPS pre---programming button (see page 370/14)

Blinking

=calib-

ration can

be done

=gas pedal ca-

librating mode

FIII

=set-

ting mode

symbol

3. When the gas pedal calibration has been selected and

confirmed (

is visible in the LH side segment),

digits

start to blink in the two RH side segments (2 Hz).

This indicates that the calibrating can be done.

4. Set the mechanical gears in neutral (engine at low idling).

Raise the engine revs evenly and gently with the throttle

lever up to max. revs during about 10 seconds, however all

the time the revs must go up. When the max. revs have

been reached,

wait about 3 seconds

and press the HiShift

button. At which time the control unit reads values in the

calibrating points and saves them in a memory. Lower to

the low idling speed. After the successful calibration digits

appear in the two RH side segments. If the calibration is

not successful, began the calibration again and raise once

again the revs slower during 12---15 seconds with the hand

gas lever. When you approach max. revs can the depres-

sing of the pedal be slowed a bit

Note!

If the calibration failed (

without blinking in the two

RH side segments), the values are not saved and the earlier

values remain in power. In this case the calibration must be

repated. The calibrating mode is left by switching off cur-

rent.

If the calibration is not successful after several attempts or

DPS has malfunctions, (specially low rews models

6750

and

8350

). Do the calibration with the computer, instr. on

page

370/19B

If the calibration failed, so:

--- check the pump position sensor, see instr.

on page

370/24

(AC 5) or on page

371/14

(AC 5.2).

--- check the position sensor wires

--- check function of the engine speed sensor

B11

. See

page

370/12.

--- If the sensor and its wires are OK, the fault may lie in the

control unit and it must be changed.

--- check engine speeds: low idling speed must be under

1000 rpm and max speed over 1800 rpm.

IMPORTANT!

Escape from this mode by switching off cur-

rent.

C. Calibrating clutch pedal, AC 5 and 5.2

The clutch pedal is calibrated if:

--- test mode indicated that the pedal function is not within the

given limits

--- Fault code

A314, A315

d225

(front controls) or

A351

A128

d254

(reverse drive controls) appeared in the display.

--- pedal position sensor has been changed

IMPORTANT!

Before calibration, check the pedal sensor volt-

ages in AC 5, see page

370/23

. When selecting the clutch

pedal calibration, the pedal must be in the upper position.

1. Activate the setting mode according to instr. A on page

370/14.

2. Select in the setting mode menu number 2 with the DPS

push buttons (in the speed gear lever knob) and confirm it

with the DPS pre---programming button (see page 370/14)

Blinking

calibration can be

done.

=clutch

pedal ca-

librating

mode

FIII

=set-

ting mo-

de sym-

bol

3. After the clutch pedal calibration has been selected and

confirmed (

is visible in the LH side segment), two digits

start to blink in the two RH side segments (2 Hz). This indi-

cates that the calibration can be done.

4. Depress the clutch pedal

gently

and

evenly

to the bottom

and keep the pedal in bottom for a while, at which time the

control unit reads values in the calibrating points and saves

them in memory. After the successfully calibration digits

appear in the two RH side digits.

Note!

If the calibration failed (01 did not appear), the values

are not saved. Old values remain in the memory and the ca-

libration must be repeated.

If the calibration failed, so:

--- check the clutch pedal potentiometer, see instr.

on page

370/23

--- check the pedal limit switch function and adjustment.

--- Check the wires of these components

--- If these are OK, the fault may lie in the control unit.

IMPORTANT!

Escape from this mode by switching off cur-

rent.

NOTE!

Calibrate in the same way the rear clutch pedal of the

optional reverse drive control (TwinTrac).

Summary of Contents for VALMET 6000


















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for VALMET 6000

Reviews:

Related manuals for VALMET 6000

Brands by name

Popular brands

Valtra VALMET 6000, Workshop Manual

Search results

Summary of Contents for VALMET 6000

Reviews:

Related manuals for VALMET 6000

Brands by name

Popular brands