Valtra VALMET 6000 Workshop Manual Download

Page: 553 / 1361

506

Model

Code

Page

37. Autocontrol 5.2 (K41107---)

1. 8. 2000

371

6250--8950

C. Automatic speed change of DPS

(Au-

toDPS)

1. Auto2 --function

AutoDPS Auto2 function has been changed so that the

automatic gear change occurs at adjusted engine revs. The

limit revs can be adjusted as follows:

--- ensure that the shuttle lever is in the neutral position

--- switch on Auto2 with the rocker switch

--- press for one second DPS---preprogramming button

After this the present change---down limit revs are blinking

in the display and the black arrow downwards is blinking.

The blinking revs can be stepped with DPS push buttons at

intervals of 50 rpm in both directions. The limit revs for the

change---down can be altered between 900---2300 rpm.

After the change---down limit revs are correctly set, press

the DPS---preprogramming button after which the limit revs

for change---up starts to blink in the display and the black

arrow upwards is flashing. Also these revs can be stepped

at intervals of 50 rpm.

The limit revs for change---up can be adjusted between

1000---2400 rpm and it must be at least 100 rpm bigger

than the change---down revs.

When the change---up limit revs are correctly set, press the

DPS---preprogramming button after which the set revs func-

tion as limit revs in the Auto2 function.

The adjusted limit revs remain in the memory although the

current is switched off. Factory values of the limit revs are

1400 and 2100 in normal tractors and 1100 and 1700 in low

rev tractors.

Note!

While the limit revs setting mode is activated, the

control unit does engage neither driving direction (R or F). If

the driving direction is tried to engage during setting, the

indication arrow of the direction in question is flashing, but

the direction is not engaged. After this the direction can not

be engaged until the setting is completed and the parking

brake is engaged. After the parking brake has been enga-

ged, the control unit is in the normal function.

The following digital inputs affect the function:

d01

=DPS---push button up

d02

=DPS---push button down

d07

=AutoDPS rocker switch Auto1 and Auto 2

d08

=DPS auto/manual

d09

=Direction F (forward driving selected)

d10

=Direction R (rearwards driving selected)

d11

=DPS---preprogramming button

d16

=parking brake

The following frequency input:

=engine rotation speed sensor

The switches and sensors can be checked in the test mode

FII

If the input signals are OK, but malfunctions appear, the

fault can lie in the control unit of AC 5.2.

2. Speed Matching of DPS

The Speed Matching is one part of the AutoDPS function.

With the aid of the speed matching the DPS speed is chan-

ged automatically to a best suitable speed in connection

with the mechanical gear change.

The function is active, when:

--- AutoDPS is switched on (auto1 or auto2) and

--- tractor is in motion and

--- either driving directions is on.

When these terms come true, the speed matching is acti-

vated and it remains on until one of the following terms co-

mes thrue:

--- AutoDPS is switched off (Man position) or

--- tractor is stopped

When the speed matching is activated, the control unit ob-

serves whether one of the following terms comes thrue:

--- HiShift---button is pressed or

--- clutch pedal is depressed or

--- selected driving direction (F or R) is switched off

If one of the above given terms comes thrue, the control

unit measures immediately the input frenquency from sen-

sors F4/F5 (F4

in the beginning

), and with the aid of these inputs

the control unit calculates the comparison values.

When the driving direction is switched on again (HIShift

button is released, clutch pedal is released or driving direc-

tion is reselected), the control unit measures the frequency

from sensors F4/F5 at this moment (F4

in the end

This measured frequency is compared with the comparison

values and the control unit is carried out an automatic DPS

speed change (the automatic speed change can be one or

two step up or down), if the measured frequency is above

or below the calculated limit values.

The control unit changes first the DPS speed and after this

engages the traction (shuttle). If there is no need to change

the DPS speed, the traction engages immediately.

Note!

During the automatic speed change can happen that

it is not possible to change two steps up or down (e.g DPS

speed II is selected and the speed matching should be two

steps upwards). In this case the speed matching is one

step up.

The following digital inputs affect the function:

d03

=HiShift---button

d06

=Clutch pedal limit switch

d07

=AutoDPS rocker switch Auto1 and Auto 2

d08

=DPS auto/manual

d09

=Direction F (forward driving selected)

d10

=Direction R (rearward driving selected)

The following frequency inputs:

=gearbox speed (driving speed)

=reverse shuttle speed (upper sensor)

=reverse shuttle speed (lower sensor)

The switches and sensors can be checked in the test mode

FII

If the input signals are OK, but malfunctions appear, the

fault could be in the control unit of AC 5.2.

Summary of Contents for VALMET 6000


















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for VALMET 6000

Reviews:

Related manuals for VALMET 6000

Brands by name

Popular brands

Valtra VALMET 6000, Workshop Manual

Search results

Summary of Contents for VALMET 6000

Reviews:

Related manuals for VALMET 6000

Brands by name

Popular brands