background image

 

© March 2018 Van Essen Instruments. All rights reserved. 

www.vanessen.com 

Contact details:  

Van Essen Instruments B.V.  

Van Essen Instruments - Canada 

Delftechpark 20 

630 Riverbend Drive, Suite 100 

2628 XH  Delft  

Kitchener, ON, 

The Netherlands  

Canada N2K 3S2 

Phone: +31 15 275 5000 

Phone: +1 226-791-6499 

 

Internet: 

www.vanessen.com

  

Support: 

diver@vanessen.com

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Copyright © 2017 by Van Essen Instruments B.V. All rights reserved. This document contains 
proprietary information which is protected by copyright. No part of this document may be 
photocopied, reproduced, or translated to another language without the prior written consent of 
Van Essen Instruments B.V. 

Van Essen Instruments B.V. makes no warranty of any kind with regard to this material, including, 
but not limited to, its fitness for a particular application. Van Essen Instruments B.V. will not be liable 
for errors contained herein or for incidental or consequential damages in connection with the 
furnishing, performance, or use of this material. In no event shall Van Essen Instruments B.V. be 
liable for any claim for direct, incidental, or consequential damages arising out of, or in connection 
with, the sale, manufacture, delivery, or use of any product. Van Essen Instruments and the Van 
Essen Instruments logo, Diver are trademarks or registered trademarks Van Essen Instruments B.V.  

The presence of the Waste Electrical and Electronic Equipment (WEEE) marking on the product 
indicates that the device is not to be disposed via the municipal waste collection system of any 
member state of the European Union. For products under the requirement of WEEE directive 
(2012/19/EU), please contact your distributor or local Van Essen Instruments B.V. office for the 
proper decontamination information and take back program, which will facilitate the proper 
collection, treatment, recovery, recycling, and safe disposal of the device. 

 

Summary of Contents for AS346

















Reviews: