background image

17

Troubleshooting

For information about parts, accessories, or service -- contact your dealer directly or contact VanGuard 

Microscopes at 1-800-423-8842.

I can’t see anything through the eyepieces/camera

Step #

Possible Cause

How to Check

Result

Solution

For More Info

1

Light not turned on

Visually inspect

Turned on

Go to next step

Not turned on

Turn on light

Page 10

2

VLC set too low

Visually inspect

Not set too low

Go to next step

Set too low

Increase VLC

Page 10

3

Objectives not installed

Visually inspect

Installed

Go to next step

Not installed

Install objectives

Page 7

4

Condenser not installed

Visually inspect

Condenser installed

Go to next step

Condenser not installed

Install condenser

Page 7

5

Prism slider pulled out/pushed 

in (trinocular models only)

Visually inspect

Prism slider in correct 

position

Go to next step

Prism slider not in 

correct position

Pull out for camera/push in for eyepieces Page 12

6

Something blocking light path 

between substage illuminator 

and objectives

Visually inspect

Blockage

Remove blockage

No blockage

Contact dealer or VanGuard Microscopes Page 17

I can’t focus on the specimen

Step #

Possible Cause

How to Check

Result

Solution

For More Info

1

Up-stop set too low

Visually inspect

Set too low

Reset up-stop to appropriate height

Page 11

Not set too low

Go to next step

2

Using the 100X objective 

without immersion oil

Visually inspect

Using oil

Go to next step

Not using oil

Use immersion oil

Page 13

3

Condenser not installed

Visually inspect

Condenser installed

Go to next step

Condenser not installed

Install condenser

Page 7

4

Oil in objective/dirty objectives

Visually inspect

Objectives clean

Go to next step

Objectives dirty

Clean or replace objectives

Page 15

5

Slide placed on stage upside 

down

Visually inspect

Slide upside down

Flip slide

Slide not upside down

Go to next step

6

Cover glass too thick

Visually inspect

Cover glass too thick

Use #1.5 (0.17mm) cover glass

Cover glass not too thick

Contact dealer or VanGuard Microscopes Page 17

The stage keeps drifting down

Step #

Possible Cause

How to Check

Result

Solution

For More Info

1

Focus tension is set too low

Check focus tension 

control knob  (page 10)

Not enough tension

Increase tension

Page 10

Plenty of tension

Contact dealer or VanGuard Microscopes Page 17

Summary of Contents for 1200CM Series





















Reviews: