background image

 11 

F

OR

 F

UTURE 

R

EFERENCE

 

Speaker Serial Numbers: 

Purchase Date: 

5 year warranty applied for:          and received: 

Dealer Name: 

Dealer Address: 

Dealer Phone: 

Dealer Contact: 

S

PECIFICATIONS

 

Acoustic  
Coupler: 

10” with critically damped long-fiber cone and 
heavy duty 1.5”, four-layer voice coil with venti-
lated aluminum former. 
Range of operation: 28Hz to 35Hz. 

Woofer: 

8” with die-cast basket and curvilinear polycone. 
1.5 inch, two-layer voice coil with ventilated alumi-
num former. 40oz foucused-gap magnet structure. 
Range of operation: 35Hz to 600 Hz. 

Midrange: 

4.5” with die-cast basket, linear surond and curvilin-
ear polycone. Ferrofluid voice coil cooling. 
Range of operation: 600Hz to 5kHz. 

Woofer: 

1” critically damped metal alloy dome with ferro-
fluid voice coil cooling. 
Range of operation: 5kHz to 30kHz. 

Crossover: 

600Hz and 5kHz. 
First-order, 6dB per octave. Allows bi-wiring with a 
single amplifier or vertical bi-amplification with 
two identical amplifiers. 

Impedance: 

7 ohms nominal. 4 ohms minimum. 

86db with 2.83 volts of pink noise input  
at 1 meter on axis. 

28Hz to 29kHz       3db. 
32Hz to 21Hz         1.5db 

40 to 160 watts per channel into 8 ohms. 

Main or surround speakers. 
The Model 2Ce Signature is not mag-
netically shielded and should be posi-
tioned at least 10” away from the direct 

39.75” high x 16” wide x 10.25” deep. 
60 pounds net, 71 pounds gross each. 

Efficiency: 

Response: 

Recommended 
Amplification: 

Video 
Applications: 

Physical: 

     Specifications and design subject to change without 
notice due to continuing research and development. 

VANDERSTEEN AUDIO 

116 W

EST

 F

OURTH

 ST. 

H

ANFORD

, CA 93230 

(559) 582-0324 

www.vandersteen.com 

Model Treo Operation Manual. 

11 

Summary of Contents for TREO













Reviews: