background image

15

106516

OWNER’S MANUAL

VENTING
INSTALLATION

Continued

HIGH ALTITUDE
INSTALLATION

Your Vanguard direct-vent fireplace has
been AGA tested and approved for eleva-
tions from 0-2000 feet and CGA certified
for elevations from 0-4500 feet.

When installing this fireplace at an elevation
above 2000 feet (in the USA), you may need
to decrease the input rating by changing the
existing burner orifice to a smaller size. Re-
duce input 4% for each 1000 feet above sea
level. Check with your  local gas company for
proper orifice size identification.

When installing this fireplace at an eleva-
tion above 4500 feet (in Canada), check
with local authorities.

Consult your local gas company to help de-
termine the proper orifice for your location.

For assistance with any high altitude instal-
lation contact DESA International’s Tech-
nical Service Department at 1-800-DESA-
LOG (1-800-337-2564).

PARTS LISTS FOR VENTING
KITS AND COMPONENTS

Vanguard Rigid Venting

Number Description

BGFVK

Basic Ground Floor Rigid Vent Kit

Includes: 7" x 60

°

 Elbow, Extended

Adjustable Horizontal Termination,
Wall Thimble and 14 Screws

CVK

Corner Vent Kit

Includes: 7" x 30º Elbow, 7" x 90º
Elbow, 7" Adjustable Galvanized
Pipe (7-12"), 6" Pipe, Wall
Thimble, Horizontal Termination,
RTV Silicone and 20 Screws

BVK

Basement Rigid Vent Kit

Includes: 7" x 30

°

 Elbow, 7" x 4'

Galvanized Pipe, 7" x 90

°

 Elbow, 7"

Adjustable Galvanized Pipe (7-12"),
Wall Thimble, Horizontal Termi-
nation, RTV Silicone and 20 Screws

SVK

Snorkel Rigid Vent Kit

Includes: 7" x 30

°

 Elbow, 7" x 4'

Galvanized Pipe, 7" x 90

°

 Elbow, 7"

Adjustable Galvanized Pipe (7-12"),
Wall Thimble, 36" Snorkel Termi-
nation, RTV Silicone and 28 Screws

Number Description

RVF

Roof Rigid Vent Kit

Includes: Flue Restrictor, Storm
Collar, 7" x 30

°

 Elbow, 7" x 4'

Galvanized Pipe, 7" x 2' Galva-
nized Pipe, 7" Adjustable Galva-
nized Pipe (7-12"), Firestop Sup-
port, Roof Flashing, RTV Silicone,
Vertical Termination, and 26 screws

D1000

7" x 12" Galvanized Coaxial
Pipe (6 pcs.)

D1010

7" x 24" Galvanized Coaxial
Pipe (6 pcs.)

D1020

7" x 48" Galvanized Coaxial
Pipe (6 pcs.)

D1030

7" Adjustable (7-12")

Galvanized Coaxial Pipe

(6 pcs.)

D1050

7" x 6" Galvanized Coaxial
Pipe (6 pcs.)

D2000

7" x 90

°

 Elbow (6 pcs.)

D2010

7" x 45

°

 Elbow (6 pcs.)

D2020

7" x 30

°

 Elbow (6 pcs.)

D2030

7" x 60

°

 Elbow (6 pcs.)

D3000

Wall Strap/Offset Support
(6 pcs.)

D3010

Storm Collar (6 pcs.)

D3020

Wall Thimble (6 pcs.)

D3040

Vertical Vent Termination Cap

D3050

Vertical Restrictor (6 pcs.)

D3060

Ceiling Firestop/Support
(6 pcs.)

D3070

Rectangular Horizontal Rigid
Vent Termination Cap

D3071

Adjustable Horizontal Rigid

Vent Termination Cap

D3090

Cathedral Ceiling Support Box

D4000

Roof Flashing 6/12-9/12

D4010

Roof Flashing 9/12-12/12

D5000

Wood/Vinyl Siding Standoff
(6 pcs.)

SIMPSON DURA-VENT
GS 4" x 6 

5

/

"

Number Description

Available from DESA International:

SD2040

Simpson Dura-Vent GS
30

°

 Elbow (6 pcs.)

SD2050

Simpson Dura-Vent GS
60

°

 Elbow (6 pcs.)

Available from Simpson Dura-Vent only:

902

7" x 48" Pipe

903

7" x 36" Pipe

904

7" x 24" Pipe

906

7" x 12" Pipe

907

7" x 9" Pipe

908

7" x 6" Pipe

911

7" Adjustable (11"-14 

5

/

8

") Pipe

940

Wall Thimble

941

Cathedral Ceiling Support Box

943

Roof Flashing 0/12-6/12

943S

Roof Flashing 7/12-12/12

945

7" x 45

°

 Elbow

950

Vinyl Siding Standoff

953

Storm Collar

963

Ceiling Firestop

981

36" Snorkel Termination

984

Horizontal Termination Vent Cap

988

Wall Strap

990

7" x 90

°

 Elbow

991

Vertical High Wind Termination

Vanguard Flexible Venting 

(Cont.)

Number Description

BFGFVK

Basic Flex Ground Floor Vent Kit

Includes: Flex Adapter, 7" x 2'
Flexible Pipe, 4" x 2' Flexible
Pipe, Wall Thimble, Horizontal
Termination, (2) Spacer Springs,
(2) 4" Hose Clamps, (2) 7" Hose
Clamps, and 10 Screws

Vanguard Rigid Venting 

(Cont.)

Vanguard Flexible Venting

Number Description

FGFVK

Flex Ground Floor Vent Kit

Includes: Flex Adapter, 7" x 4'
Flexible Pipe, 4" x 4' Flexible Pipe,
Wall Thimble, Horizontal Termi-
nation, (4) Spacer Springs, (2) 4"
Hose Clamps, (2) 7" Hose Clamps,
RTV Silicone, and 10 Screws

D1040

7" x 25' Coaxial Flex Pipe
with Spacer Springs

D3080

Rectangular Horizontal
Flex Termination Cap

D4020

Flex Connector (6 pcs.)

D4030

Flex Wall Thimble (6 pcs.)

D4040

4" Hose Clamp (6 pcs.)

D4050

7" Hose Clamp (6 pcs.)

Summary of Contents for BHDV34PB







































Reviews: