background image

WARING:

NEVER remove the NexStar MX while the hard drive is in 
use. Doing so may corrupt the data on the hard drive or 
damage the hard drive, NexStar MX and the computer.

Disconnecting the NexStar MX

14

8.Disconnecting the NexStar MX:

     Dual 3.5” RAID Enclosure w/Fan USB 3.0 & eSATA Interface

Microsoft Windows XP/Vista/7:

Make sure all operations using the hard 
drive within the NexStar MX has ceased. 

Close any windows and programs 
pertaining to the NexStar MX 

Double click the green “Safely Remove 
Hardware” icon in the system tray and 
select [Safely Remove USB Mass Storage 
Device]. Select the device you wish to 
remove and click on [Stop]. The system 
should prompt, “It is now safe to remove 
the USB device.” If not, wait for any 
programs still using the device to finish and 
try again. 

You may now safely turn off and disconnect 
the NexStar MX.

Mac OS:

Make sure all operations using the hard 
drive within the NexStar MX has ceased.

Close any windows and programs 
pertaining to the NexStar MX

From the Desktop, drag the NexStar MX 
hard drive to the trash.

You may now safely turn off and disconnect 
the NexStar MX.

Summary of Contents for NexStar MX
























Reviews: