background image

 

17 

by independent scientific organizations through evaluation of scientific studies. The 

standards include a substantial safety margin designed to assure the safety of all persons 

regardless of age or health. The SAR limit of USA (FCC) is 1.6W/Kg averaged. Has also 

been tested against this SAR limit. SAR information on this and other pad can be viewed 

on-line at http://www.fcc.gov/oet/ea/fccid/. Please use the device FCC ID number for 

search. To maintain compliance with FCC RF exposure requirements, the use of belt clips, 

holsters and similar accessories should not contain metallic components in its assembly, 

the use of accessories that do not satisfy these requirements may not comply with FCC 

RF exposure requirements, and should be avoided 

 

ISED Canada compliance statement 

this device complies with ISED Canada license-exempt RSS standard(s). Operation is 

subject to the following two conditions: (1) this device may not cause interference, and (2) 

this device must accept any interference, including interference that may cause undesired 

operation of the device. 

Operation in the band 5150

–5250 MHz is only for indoor use to reduce the potential for 

harmful interference to co-channel mobile satellite systems. 

RF exposure information and statement: 

This equipment complies with IC RSS-102 

radiation exposure limits set forth for an uncontrolled environment. The guidelines are based 

on standards that were developed by independent scientific organizations through periodic 

and thorough evaluation of scientific studies. The standards include a substantial safety 

margin designed to assure the safety of all persons regardless of age or health. The SAR 

limit of ISED is 1.6W/Kg averaged. Has also been tested against this SAR limit. To maintain 

compliance with ISED RF exposure requirements, the use of belt clips, holsters and similar 

accessories should not contain metallic components in its assembly, the use of accessories 

that do not satisfy these requirements may not comply with ISED RF exposure 

requirements, and should be avoided.   

Le présent appareil est conforme aux CNR d’ISDE Canada applicables aux appareils radio 

exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1)l’appareil 

ne doit pas produire de brouillag

e, et (2) l’appareil doit accepter tout brouillage 

radioélectrique subi, même si le brouillage est susceptible d’en compromettre le 

fonctionnement. 

La bande 5150

–5250 MHz est réservée uniquement pour une utilisation à l’intérieur afin 

de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles 

utilisant les mêmes canaux. 

Information et déclaration sur l’exposition aux RF : Cet équipement est conforme aux limites 

Summary of Contents for M10 LITE



























Reviews: