manualshive.com logo in svg

Varec 2920, Installation And Operation Manual

The Stryker 2920 Operation Manual, available for free download at 88.208.23.73:8080, is a comprehensive and user-friendly guide for getting the most out of your Stryker 2920 product. This detailed manual offers step-by-step instructions, safety guidelines, troubleshooting tips, and more, ensuring a seamless and efficient user experience.

Share
Download
background image

viii

Installation and Operations Manual

Product Order Code: N2920-aa-1-cc-2-e-2-g-h-i   . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Product Order Code: N2920-aa-2-cc-0-N-1-g-h-i  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Product Order Code: N2920-aa-2-cc-0-N-1-B-h-i  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Product Order Code: N2920-aa-2-cc-0-N-f-g-h-i   . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Product Order Code: N2920-aa-2-cc-1-e-1-N-h-i  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Product Order Code: N2920-aa-2-cc-1-e-1-A-h-i  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Product Order Code: N2920-aa-2-cc-1-e-f-g-h-i  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Product Order Code: N2920-aa-2-cc-2-e-1-N-h-i  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Product Order Code: N2920-aa-2-cc-2-e-f-g-h-i  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Connecting Wiring in the Transmitter    . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Connector Locations: Communications Circuit Board   . . . . . . . . . . . . . . . . . . . . . . . . 44
Connector Assignments: Communications Circuit Board  . . . . . . . . . . . . . . . . . . . . . . 45
   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Connector and Switch Locations: AC Power Supply Circuit Board   . . . . . . . . . . . . . . 47
Connector Assignments: AC Power Supply Circuit Board  . . . . . . . . . . . . . . . . . . . . . 47
Selecting the AC Voltage Setting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Setting Optional Outputs as NC or NO  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Wiring Limit Switches  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

5

Display and Configuration Interface  . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

Indicators  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Configuration   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
System Data   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

PIN Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Basic Setup   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Local RS-232  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
System Time   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Encoder Data    . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
RTD Data    . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Tank Data   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Digital Outputs  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Analog Input    . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Analog Input User Calibration  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Analog Out    . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Analog Output User Calibration   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

BPM Data    . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
MODBUS Data  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Mark/Space Data  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
L&J TankWay  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
NMT Prothermo  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
HART Device  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
FMR Radar   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
HART Master  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Calibration   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100

Calibrate Level Shortcut  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100

6

Bi-Phase Mark  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101

Basic Parameters    . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

7

MODBUS   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105

Basic Parameters    . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
2920 EIA-485 MODBUS Hardware Setup  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108

Summary of Contents for 2920



































































































































































































Reviews:

No comments

Related manuals for 2920

AquaMedic spectrus 60 Operation Manual preview
spectrus 60
Brand: AquaMedic Pages: 36
T&D RTR-601-130 User Manual preview
RTR-601-130
Brand: T&D Pages: 2
MAAX Utile Installation Instructions Manual preview
Utile
Brand: MAAX Pages: 60
Lascar EL-USB-1 Manual preview
EL-USB-1
Brand: Lascar Pages: 4
Crestron CAT5 Reference Manual preview
CAT5
Brand: Crestron Pages: 52
SAF P89 Service Manual preview
P89
Brand: SAF Pages: 28
LogIT Black Box Quick Start Manual preview
Black Box
Brand: LogIT Pages: 44
White Industries Diagnostic 1090AT Operation And Maintenance Manual preview
Diagnostic 1090AT
Brand: White Industries Pages: 32
ACT ACTLAN - INTERFACE Configuration preview
ACTLAN - INTERFACE
Brand: ACT Pages: 2
Telect 125DM08 Installation Manual preview
125DM08
Brand: Telect Pages: 18
Body Life LASERSERIES User Manual preview
LASERSERIES
Brand: Body Life Pages: 15
Rampage 77015 Installation Instructions Manual preview
77015
Brand: Rampage Pages: 2
Temsa TS30 2012 Electronics And Wiring Manual preview
TS30 2012
Brand: Temsa Pages: 32
Vollrath STOELTING AutoFill Installation Instructions preview
STOELTING AutoFill
Brand: Vollrath Pages: 3
Desco Europe 19588 Installation, Operation And Maintenance preview
19588
Brand: Desco Europe Pages: 5
Altec Lansing ULTRA Datasheet preview
ULTRA
Brand: Altec Lansing Pages: 2
Oase HeatUp Basis 10 W Operating Instructions And Guarantee preview
HeatUp Basis 10 W
Brand: Oase Pages: 92
less care LBSDG3072 Installation Instructions Manual preview
LBSDG3072
Brand: less care Pages: 21

Brands by name

Popular brands

Load more brands