Agatha
3.2 Operation safety
The machine is designed to protect its attendant from parts flying off the cut area. Do not remove any passive nor active safety elements. By
doing so you expose yourself to risk of injury.
3.2.1 Safety regulations
Machine attendants have to be aged
18
or over. The attendant
must be familiar
with the machine user manual and have knowledge of
general work safety principles.
Always switch off the engine and wait for the cutting disk to stop before starting any activity near the machine! Always switch the engine
off before leaving the machine!
Never leave the engine running at the maximum engine speed or running idle for a long time while the clutches of the cutting disk drive
and wheel drive are turned off. The machine drive parts could be damaged (V-belt, belt pulley, clutch pulley, etc.)!
Before each machine
use check all its parts (especially the operating mechanism and its covers) to see if they aren't loose or damaged.
Revealed
defects parts
must be
rectified immediately
. For repairs, use the original spare parts only.
Remove any solid parts form the stand before cutting (such as stones, wires, loose construction leftovers, etc.), as these could be thrown
away or damage the machine. If these parts cannot be removed, avoid them.
The machine is equipped with a rotating implement. Maximum circumferential speed is
60,9 m.s
-1
. It is therefore important to keep other
persons at a safe distance while the machine is operating (there is a possibility of the cut stand or solid objects chipping off)!
Since the recommended noise and vibration levels are exceeded, follow the following instructions when operating the machine:
a)
Protect your ears with appropriate safety devices according to
ČSN EN 352-1
(shell-shaped ear protectors) or
ČSN EN 352-2
(plug ear protectors). Ask your dealer for these safety devices.
b)
After every 20 minutes maximum of operating the machine interrupt the work for a 10 minute break. During these breaks, the
machine attendant must not be exposed to other noise or vibrations.
When operating the machine, use work aids approved by
ČSN EN 166
or
ČSN EN 1731
(tight clothes, firm shoes, work gloves and
protective glasses.) Keep a safe distance form the machine given by its handlebars.
Do not start the engine in closed spaces! Pay special attention when handling the machine. The engine exhaust muffler remains hot after
the engine is switched off. While adding the fuel, make sure it does not leak or spill over engine parts. If the fuel is spilled, dry the soiled
parts or wait for the fuel to evaporate.
When the machine is being operated, all other persons (
especially children
) and animals must stay out of the machine's workspace.
The machine attendant can only continue working after taking these into a safe distance.
It is forbidden to remove any protective devices and covers from the machine.
Safe
climbing ability of the machine is 10º. Maximum engine tilt while working is 20º for long and 30º for short periods
Any machine repairs, adjustments, greasing and cleaning is to be carried out when the machine is turned off and disconnected the spark
disconnected
.
3.2.2 Noise and vibration values
Description
DS-521
DS-521B
DS-521Z
Declared
emission level of the acoustic pressure
A
at
attendance point
L
pAd
= (80,5+1,5 dB)
L
pAd
= (82+2 dB)
L
pAd
= (84+1 dB)
Guaranteed
A
L
WA,G
= 97dB
L
WA,G
= 97dB
L
WA,G
= 98 dB
Declared
aggregate acceleration value of the vibrations
transferred onto the hand-arm of the machine attendant
a
hvd
= (6,6+2,6 m.s
-2
)
a
hvd
= (7,1+2,9 m.s
-2
)
a
hvd
= (8,0+3,0 m.s
-2
)
Tab. 2: Noise and vibration values
3.2.3 Safety pictograms
The user is required to keep the machine pictograms readable, and have them exchanged in case they are damaged.
70
Short period = up to 1 minute.
71
According to
EN 836+A4
, Appendix
H
and
EN ISO 11201:april 2010
72
According to
2000/14/EC
instructions (equivalent of NV n.9/2002 Coll., Appendix n.3, part B, point 33) and
EN ISO 3744:2010
73
According to
EN 836+A4
, Appendix
G
and
EN ISO 20643
30
R
ev
iz
e
0
4
/2
0
1
5
Summary of Contents for agatha DS-521
