background image

  

DS-520 Líza 

  DS-520H Líza

 

 

 
 

Contents 

 
1 Basic information. ............................................................................................................. 3 
2 Introduction. ...................................................................................................................... 4 

2.1 General warnings....................................................................................................... 4 

3 Operation safety. ............................................................................................................... 5 

3.1 Safety regulations. ..................................................................................................... 5 
3.2 Safety pictographs. .................................................................................................... 6 
3.3 Maximum values of noise and vibrations as measured by AO - 206 SZZPLS Praha.
 7 

4 Machine use, technical specification and technical description........................................ 7 

4.1 Machine use............................................................................................................... 7 
4.2 Technical specification.............................................................................................. 8 
4.3 Technical description of the machine........................................................................ 8 

5 Instructions for use. ........................................................................................................... 9 

5.1 Machine assembly. .................................................................................................... 9 
5.2 Putting into operation. ............................................................................................. 10 
5.3 Starting the mowing disk......................................................................................... 11 
5.4 Driving the mower. ................................................................................................. 11 
5.5 Stopping the mowing disk....................................................................................... 12 
5.6 Working with the machine. ..................................................................................... 12 

5.6.1 Cutting grass stands......................................................................................... 12 
5.6.2 Driving the mower. ......................................................................................... 12 
5.6.3 Cutting procedure. ........................................................................................... 13 
5.6.4 Problems at cutting.......................................................................................... 13 

6 Maintenance, care and storage. ....................................................................................... 14 

6.1 Machine lubrication................................................................................................. 14 

6.1.1 Engine oil replacement.................................................................................... 14 
6.1.2 Table of machine lubrication........................................................................... 14 

6.2 Tightening bolted connections. ............................................................................... 15 
6.3 Replacing and sharpening cutting blades. ............................................................... 15 
6.4 V-belt replacement and adjustment of tightening pulley. ....................................... 16 
6.5 Tightening pulley wire and drive diagnostics. ........................................................ 18 
6.6 Driving problems diagnostics.................................................................................. 18 
6.7 Table of service operations. .................................................................................... 19 
6.8 Washing and cleaning the machine. ........................................................................ 19 
6.9 Machine storage. ..................................................................................................... 20 
6.10 Disposal of packaging and machine after the end of service life............................ 20 

7 Instructions for ordering spare parts................................................................................ 21 
8 Address of the manufacturer: .......................................................................................... 21 
9 List of components. ......................................................................................................... 22 
10 List of Guarantee............................................................................................................. 29 
 
 
 
 
 

Summary of Contents for Liza DS-520
































Reviews: