background image

  

DS-520 Líza 

  DS-520H Líza

 

 

2 Introduction. 

 
Dear customer, 

Thank  you  for  the  trust  you  have  shown  by  purchasing  our  product.  You  are  now 

owner of machine from a wide range of machines and attachments made by 

,a.s. 

within a system of gardening, farming, small agricultural and communal machinery. 

Please  read  these  Instructions  for  use  carefully.  If  you  follow  the  instructions 

properly, you will have our products performing a reliable work for you for years. 
 

2.1 General warnings. 

 

The  user  is  obliged  to  get  acquainted  with  the  Instructions  for  use  and  to  follow  all 

instructions for machine operation so that the user’s and other persons’ health and property 
do not suffer any harm. 

Safety instructions contained in this manual do not describe all situations or conditions 

possibly  occurring  in  practical  use.  Safety  factors  such  as  common  sense,  diligence  and 
scrupulousness  are  not  included;  it  is  assumed,  however,  that  all  persons  authorized  for 
machine operation or maintenance do possess the intelligence. 

Only persons in good mental and physical condition can operate the machine. For the 

professional use of the machine the machine owner is obliged to ensure a work safety training 
and  provide  instructions  on  machine  control  for  operators  and  to  keep  records  on  these 
trainings and briefings. 

Should  some  instructions  in  the  manual  be  unintelligible,  you  are  encouraged  to 

contact  your  seller  or  directly  the  manufacturer  of  the  machine.  The  contact  address  and 
telephone/fax connection are to be found at the end of the manual. 

Instructions  for  use  supplied  with  the  machine  are  an  integral  part  of  the  machine. 

They have to be available at any time, placed at a well accessible place with no risk of their 
damage. If the machine is sold to another person, the Instructions for use must be given to 
the  new  machine  owner.  If  the  above  conditions  are  not  met,  the  manufacturer  bears  no 
responsibility for incurred risks, accidents and injuries resulting from the machine operation. 

The  manufacturer  bears  no  responsibility  for  damages  caused  by  unauthorized  and 

incorrect  use  of  the  machine  and  for  damages  caused  by  any  machine  modifications  not 
authorized by the manufacturer. 

To  prevent  injuries  of  operators  and  other  people  occurring  in  the  vicinity  of  the 

machine,  it  is  absolutely crucial  to  follow safety regulations  marked  in  the Instructions for 
use with the following warning safety symbol: 

 
 

,

 

On seeing this symbol in the manual, read 

the attached instructions carefully! 

 
 
 

Summary of Contents for Liza DS-520
































Reviews: