background image

 

22 

3

. Care should be taken of  cleanness of all bearing and connecting surfaces. Apply a 

thin layer of plastic lubricant MOGUL A 00 on a flange  for connecting the drive with 
the gear box. 

 
 

4

. After the end of the season remove all dirt and plant residue. 

Check that the working blades are in an undamaged condition, sharpen  cutting edges 
of blades and apply a conservation oil. 

 



5. 

When cleaning, washing the machine with water, solvents and other chemical 

agents, it is necessary to proceed in such a way to follow accepted provisions and 
regulations on the protection of rivers and streams and other water sources against 
pollution, contamination and contamination by chemical substances. 

 
 

 

 

 

 

 

 

 

 

 

 

 
 
 

VII.  STORAGE 

 
 
 

Store the machine in dry places. The access of unauthorised persons to the machine 
should be avoided. 

 

In case of a longer shut down of the machine, conserve all connecting surfaces with 
the use of a conservation oil. 

 

Protect the machine against the effects of weather. 

 

 

 
 
 
 
 

VIII.  LIQUIDATION  OF  PACKAGES 

 
 

Paper packages  - 

sale to purchase of secondary materials 

 

 

 

 

deposition on collection places in containers 

 

 

 

 

incineration 

 

 

 

 

other utilising 

 

Plastic packages  - 

deposition on collection places in containers 

 

Wood   

    - 

liquidation by incinerating,  crushing or chipping   

 

Summary of Contents for Samson - 56 BK























Reviews: