background image

10

o

PeratIon

 

of

 

the

 

mIxer

:

Before starting the mixer:

Mount the required tool in the bayonet shaft. Place the bowl 
in the bowl arms and close the bowl screen.

To raise the bowl, activate the fields 

 ,  

 and 

       

simultaneously

, the activation to be continued until the 

bowl has reached its top position. When the bowl is approx. 

20 cm from its top position, the tool will start to rotate in low 

speed. The rotation of the tool and the bowl will stop auto-
matically when the bowl is in its top position.

The red diode in the field

 

 is now alight to show that the 

mixer is ready.

Start the mixer:

Activate the field

 

 to start the mixer.

Activate the field

 

 to increase the speed.

Activate the field

 

 to reduce the speed.

The speed indicator below the fields 

 to 

 shows the 

mixing speed of the tool.

Four fixed speeds:

For quick choice of speed, use the fields 

 to 

 .

Field 

 corresponds lowest speed.

Field 

 corresponds approx. 30% of maximum speed.

Field 

 corresponds approx. 60% of maximum speed.

Field 

 corresponds maximum speed.

Indication of operation time:

Before starting the mixer, an operation time for the mixer can 
be chosen by adjusting the time on

 

 and 

 . 

If the field 

is activated for longer time, the speed is increased/reduced 
quicker.

Minutes and seconds are shown in the text field between 

 and 

 .

Automatic lowering of bowl:

Once the mixer has been started, the operator can make the 

mixer lower the bowl automatically when it stops by pressing 

.

 The diode in the field is flashing after the activation.

Inspection of the ingredients during operation:

If it is wished to stop the mixer without affecting the opera-

tion time, the field 

 can be activated. The mixer will re-

duce speed and then stop, the operation time will also stop. 
If the guard is opened, the display shows 

, but the 

operation time is displayed again when the guard is closed.

Close the bowl screen and press 

 and the mixer will start 

at the lowest speed. The operation time continues from before.

Lowering of bowl:

When the ingredients in the bowl have been mixed, the mixer 

is stopped by activating the field 

.The bowl is lowered by 

activating the field 

. When the bowl has reached its bottom 

position, the bowl screen can be opened. 

Emergency stop

Bowl up

Bowl down

Pause

Time up

Text  field

Time down

Fixed speeds

Speed indicator

Speed down

Speed up

Start/Stop

REMIX

Summary of Contents for ERGO60

























Reviews: