background image

4

SAFETY:

User safety is assured as follows:

The mixer is designed for commercial use in kitchens, catering outlets and bakeries.

The machine is designed for the manufacture of products that do not trigger any reactions or release substances 

that may be harmful to the user when in use.

The machine must not be used in an explosive atmosphere.

The machine may only be used by trained personnel.
 Always comply with local laws and regulations with special attention to operators age, physical and mental condi-

tion. Operator must be over 14 years of age. 

The constant noise  level of the workplace of the operator is lower then 70 dB (A)
Tools can only rotate when the safety guard is in place and the bowl is lifted (bowl detection).
The safety guard is made of plastic. 
It is not possible to attach the guard incorrectly.
No access to rotating tools.

The spread of flour dust is inhibited.
Equipped with emergency stop - The tool stops rotating in less than 4 seconds (also for normal shut-down and 

stop via safety guard).

Clearance between guard/stand and lifting handle at least 50 mm.

Machine remains stable even if tilted of up to 10°. 
The machine is protected against overvoltage.

Non-ionising radiation

 is not produced intentionally, but rather technically conditioned by electrical equipment (e.g. elec-

tric motors, live power lines or solenoids). The machine is equipped with strong permanent magnets. By maintaining a safe 

distance (between the field source and implant) of 30 cm, any impact on active implants (e.g. pacemakers, defibrillators) 

can likely be prevented.

 

Magnets: 

Warning for users with implants (e.g. pacemakers, defibrillators).

machine and safety guard equipped with strong magnets

Areas on machine and 

bowl with magnets - 

for bowl detection

Area on safety guard with magnets

Area on machine with 

magnets - for safety 

guard switch

Summary of Contents for KODIAK10

















Reviews: